Order Products : sales@su-jiao.com
SMOKEGUARD™ III 1011 NATURAL
| Category: | PVC, Unspecified , Polyvinyl Chloride |
| Manufacturer: | AlphaGary |
| Trademark: | SMOKEGUARD™ III |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | OscIDM_SMOKEGUARD-III-1011-NATURAL.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| A HIGHLY FLAME RETARDED, LEAD FREE 75C DEGREE LOW SMOKE JACKETING COMPOUND FOR PLENUM CABLE CONSTRUCTIONS REQUIRING COMPLIANCE TO U.L. SUBJECT 910 MODIFIED STEINER TUNNEL TEST. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.56 - 1.60 | g/cm³ | ASTM D792 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness | ASTM D2240 | ||
| Shaw D | 65 - 71 | ASTM D2240 | |
| Shaw D, 15 seconds | 51 - 57 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength (0.381 mm) | 17.2 | MPa | ASTM D412 |
| Tensile Elongation (fracture, 0.381mm) | 170 | % | ASTM D412 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Brittleness Temperature | -9.00 | °C | ASTM D746 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Dielectric Constant (23°C, 100 MHz) | 3.25 | ASTM D150 | |
| Dissipation Factor (23°C, 100 MHz) | 0.014 | ASTM D150 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Oxygen Index (3.18 mm) | 47 | % | ASTM D2863 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Cylinder Zone 1 Temp. | 149 | °C | |
| Cylinder Zone 2 Temp. | 154 | °C | |
| Cylinder Zone 3 Temp. | 163 | °C | |
| Cylinder Zone 4 Temp. | 168 | °C | |
| Cylinder Zone 5 Temp. | 168 | °C | |
| Adapter Temperature | 154 | °C | |
| Melt Temperature | 179 - 185 | °C | |
| Die Temperature | 154 | °C | |
| Extruder Screw Compression Ratio | 3.0:1.0 |
| Extrusion instructions |
|---|
| Melt temperature is critical, at temperatures above 370 degrees F foaming may occur. It may be necessary to adjust barrel temp to attain the desired melt temperature. Material should be dried prior to use. |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| VYLOPET® EMC545 | TOYOBO America, Inc. | PC+PBT | VYLOPET® |
| Aegis® H120MP | Honeywell | Nylon 6 | Aegis® |
| ALCUDIA® LDPE PE-015 | REPSOL | LDPE | ALCUDIA® LDPE |
| Aropol™ L 65305 resins | Ashland Performance Materials | Polyester, TS | Aropol™ |
| Durethan® AKV 50 H3.0 000000 | LANXESS GmbH | Nylon 66 | Durethan® |
