Order Products : sales@su-jiao.com
Boda BDF275P
| Category: | Fluorelastomer , Fluoroelastomer |
| Manufacturer: | Chenguang Fluoro & Silicone Elastomers Co., Ltd. |
| Trademark: | Boda |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | 2Ek4Ds_Boda-BDF275P.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
BDF275P is a low viscosity curative incorporated fluoroelastomer copolymer. This grade is well suited for application where good flowability and excellent mold release property are required. BDF275P can be compounded to meet the major fluoroelastomer specifications. BDF275P can be used for injection molding of O-rings and gaskets, or extrusion of complicated geometries. It can be mixed using typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Finished goods can be produced by a variety of rubber processing methods. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Appearance |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.80 | g/cm³ | |
| Mooney Viscosity (ML 1+10, 121°C) | 20 | MU | |
| Fluorine Content | 66 | % | |
| Solubility | LMW Ketones and esters |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| MH 1(177°C) | 1.30 | N·m | |
| ML 2(177°C) | 0.150 | N·m | |
| t'90 3(177°C) | 2.0 | min | |
| ts2 4(177°C) | 50.0 | sec |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness 5(Shore A) | 76 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength 6(Yield) | 11.0 | MPa | ASTM D412 |
| Tensile Elongation 7(Break) | 240 | % | ASTM D412 |
| Compression Set (200°C, 70 hr) | 22 | % | ASTM D395B |
| Additional Information |
|---|
| Test Compound: Polymer: 100 MT Black (N990): 30 phr MgO: 3 phr Ca(OH)2: 6 phr Curing Condition: Press: 10 min at 170°C Oven: 24 hr at 230°C |
| Note Message | |
|---|---|
| 1 . | MDR2000 Rheometer, 100cpm, 0.5° Arc, 6 minutes |
| 2 . | MDR2000 Rheometer, 100cpm, 0.5° Arc, 6 minutes |
| 3 . | MDR2000 Rheometer, 100cpm, 0.5° Arc, 6 minutes |
| 4 . | MDR2000 Rheometer, 100cpm, 0.5° Arc, 6 minutes |
| 5 . | Press Time: 10 min, Press Temperature: 170°C, Post Cure Time: 24 hr, Post Cure Temperature: 230°C |
| 6 . | Press Time: 10 min, Press Temperature: 170°C, Post Cure Time: 24 hr, Post Cure Temperature: 230°C |
| 7 . | Press Time: 10 min, Press Temperature: 170°C, Post Cure Time: 24 hr, Post Cure Temperature: 230°C |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Unitex Chemical DNHP | Unitex Chemical Corporation | Plasticizer | Unitex |
| ALCOM® PC 740/4.1 WT1056-09LD2 | ALBIS PLASTIC GmbH | PC | ALCOM® PC |
| Anjatech® 250-E/H/GF15 | Almaak International GmbH | Nylon 6 | Anjatech® |
| ExxonMobil™ PP1013H1 | ExxonMobil Chemical | PP Homopolymer | ExxonMobil™ |
| HiFill® PBT GF20 BK007 | Techmer Engineered Solutions | PBT | HiFill® |
