Order Products : sales@su-jiao.com
OnFlex™ S EH 60A-3S7003
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | PolyOne Corporation |
| Trademark: | OnFlex™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | zcSHnu_OnFlex-S-EH-60A-3S7003.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| OnFlex™ S EH thermoplastic elastomer compounds are based on hydrogenated styrenic block copolymers. This range of compounds are formulated to deliver a great cost/performance ratio in addition to typical OnFlex™ S properties such as a wide hardness range, good mechanical properties, good processability, good colourability and a wide temperature operating range. OnFlex™ S EH compounds are filled, and are therefore opaque and have a moderately high density. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| RoHS Compliance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.20 | g/cm³ | ISO 1183 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A) | 60 | ISO 868 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress | ISO 37 | ||
| 100% strain | 2.30 | MPa | ISO 37 |
| 300% strain | 3.10 | MPa | ISO 37 |
| Tensile Stress (Break) | 5.00 | MPa | ISO 37 |
| Tensile Elongation (Break) | 600 | % | ISO 37 |
| Tear Strength | 25 | kN/m | ISO 34-1 |
| Compression Set | ISO 815 | ||
| 23°C, 72 hr | 25 | % | ISO 815 |
| 70°C, 22 hr | 51 | % | ISO 815 |
| 100°C, 22 hr | 78 | % | ISO 815 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Fogging | 1.3 | mg | DIN 75201B |
| Additional Information | Nominal Value | Test Method | |
|---|---|---|---|
| Odor rating | 3.00 | VDA 270 | |
| General Material Type | Styrene thermoplastic elastomers (TES) | ||
| 各项属性值是采用注射模制基板测量得出。 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Processing (Melt) Temp | 180 - 220 | °C | |
| Mold Temperature | 30.0 - 60.0 | °C | |
| Injection Rate | Fast |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Shandong PA1212 Reinforced Nylon 1212 | Shandong Guangyin New Materials Co., Ltd. | Nylon 1212 | Shandong PA1212 |
| VITAMIDE® AR36GY6581 | Jackdaw Polymers | Nylon 66 | VITAMIDE® |
| Nanjing Hongrui PC CS1000 | Nanjing Hongrui Engineering Plastics Co., Ltd. | PC | Nanjing Hongrui PC |
| LG PVC LS130S | LG Chem Ltd. | PVC Homopolymer | LG PVC |
| POLYelast TPE R44 TV10 | Polykemi AB | PP+EPDM | POLYelast |
