Order Products : sales@su-jiao.com
MAGNUM™ 347 EZ
| Category: | ABS , ABS Resin |
| Manufacturer: | Trinseo |
| Trademark: | MAGNUM™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | vO5Tmq_MAGNUM-347-EZ.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
MAGNUM ABS resins are thermoplastic materials which provide an excellent balance of processability, impact resistance and heat resistance as imparted by the various polymer compositions. MAGNUM ABS resins are available in a wide range of melt flow rates, impact strength and heat resistance for both high and low gloss applications manufactured by injection molding, sheet or profile extrusion and thermoforming processes. Automotive MAGNUM ABS resins offer a wide range of gloss, viscosity, impact strength and heat properties for use in numerous automotive applications. Melt flow rates from 1 to 12 g/10 min, impact strengths from 2.4 to 11 ft-lb/in and heat distortion temperatures from 171°F to 194°F are available. Available primarily as natural plus concentrates, MAGNUM ABS resins are used in a wide variety of automotive applications including structural instrument panels, consoles, pillars, and exterior trim parts requiring painting and plating. MAGNUM 347 EZ ABS resin is a higher flow version of 342 EZ having slightly lower impact strength. The melt flow rate of approximately 12 g/10min is often suitable for parts with long flow lines and minimal impact requirements. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | |||
| -- | 1.04 | g/cm³ | ASTM D792 |
| -- | 1050 | kg/m³ | ISO 1183 1 |
| Melt Mass-Flow Rate (MFR) (230°C/3.8 kg) | 12 | g/10 min | ASTM D1238 |
| Melt volume-flow rate (220°C/10.0 kg) | 43.0 | cm³/10min | ISO 1133 2 |
| Molding Shrinkage - Flow | 0.40 to 0.70 | % | ASTM D955 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus | |||
| -- 3 | 2070 | MPa | ASTM D638 |
| -- | 1890 | MPa | ISO 527-2 4 |
| Tensile Strength | |||
| Yield 5 | 41.4 | MPa | ASTM D638 |
| Yield | 34.0 | MPa | ISO 527-2 6 |
| Tensile Elongation | |||
| Yield 7 | 2.5 | % | ASTM D638 |
| Yield | 2.2 | % | ISO 527-2 8 |
| Break 9 | 30 | % | ASTM D638 |
| Nominal strain at break | > 50 | % | ISO 527-2 10 |
| Flexural Modulus 11 | 2170 | MPa | ASTM D790 |
| Flexural Strength 12 | 65.5 | MPa | ASTM D790 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Charpy notched impact strength | ISO 179/1eA 13 | ||
| -30°C | 5.00 | kJ/m² | |
| 23°C | 8.00 | kJ/m² | |
| Charpy impact strength | ISO 179/1eU 14 | ||
| -30°C | 90.0 | kJ/m² | |
| 23°C | 140 | kJ/m² | |
| Notched Izod Impact 15(23°C, 3.20 mm) | 130 | J/m | ASTM D256 |
| Instrumented Dart Impact 16 | ASTM D3763 | ||
| 23°C, 3.20 mm, Peak Energy | 28.2 | J | |
| 23°C, 3.20 mm, Total Energy | 35.0 | J |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load | |||
| 0.45 MPa, Unannealed, 3.20 mm | 85.0 | °C | ASTM D648 |
| 0.45 MPa | 88.0 | °C | ISO 75-2 17 |
| 1.8 MPa, Unannealed, 3.20 mm | 73.9 | °C | ASTM D648 |
| 1.8 MPa | 77.0 | °C | ISO 75-2 18 |
| Vicat Softening Temperature | |||
| -- | 102 | °C | ASTM D1525 |
| 50°C/h, B (50N) | 94.0 | °C | ISO 306 19 |
| CLTE - Flow | 7.6E-5 | cm/cm/°C | ISO 11359-2 20 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 82.2 to 85.0 | °C | |
| Drying Time | 2.0 to 4.0 | hr | |
| Suggested Max Moisture | 0.10 | % | |
| Processing (Melt) Temp | 216 to 232 | °C | |
| Mold Temperature | 26.7 to 48.9 | °C | |
| Back Pressure | 0.345 to 3.45 | MPa | |
| Clamp Tonnage | 2.8 to 4.1 | kN/cm² | |
| Screw L/D Ratio | 20.0:1.0 | ||
| Screw Compression Ratio | 1.5:1.0 to 3.5:1.0 |
| Note Message | |
|---|---|
| 1 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 2 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 3 . | Type I, 51 mm/min |
| 4 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 5 . | Type I, 51 mm/min |
| 6 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 7 . | Type I, 51 mm/min |
| 8 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 9 . | Type I, 51 mm/min |
| 10 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 11 . | Type I, 1.3 mm/min |
| 12 . | Type I, 1.3 mm/min |
| 13 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 14 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 15 . | 0.25 mm Notch Depth |
| 16 . | 3.39 m/sec |
| 17 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 18 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 19 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 20 . | Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Sinvicomp SIZ5908A | Teknor Apex Asia Pacific PTE. LTD. | PVC, Flexible | Sinvicomp |
| Complet® LCF40-PP | PlastiComp, Inc. | PP Homopolymer | Complet® |
| EnCom PC 1212 | EnCom, Inc. | PC | EnCom |
| LNP™ THERMOCOMP™ HB006 compound | SABIC Innovative Plastics | Nylon 11 | LNP™ THERMOCOMP™ |
| Sylvin 2990-76 Green 3206 | Sylvin Technologies Incorporated | PVC, Unspecified | Sylvin |
