AXELERON™ CS K-3364 NT CPD Datasheet,HDPE,The Dow Chemical Company-SHANGHAI SUSHENG

AXELERON™ CS K-3364 NT CPD

Wechat: WECHAT

Message
AXELERON™ CS K-3364 NT CPD is a high-molecular weight, high-density polyethylene insulation compound ("CPD") specifically formulated to provide excellent oxidative stability, toughness, and abrasion resistance. It provides superior long term aging performance, while providing excellent environmental and thermal stress-cracking resistance. In addition, AXELERON™ CS K-3364 NT CPD provides excellent processability for high-speed wire insulating extrusion processes. AXELERON™ CS K-3364 NT CPD provides good performance for telephone insulation applications, primarily cable designs for aerial environments. AXELERON™ CS K-3364 NT CPD is optimized to meet major international age testing standards and specifications for both solid and foam/skin insulation use. Specifications AXELERON™ CS K-3364 NT CPD meets the following raw material specifications: ASTM D 1248 Type III Category A-4, Grade E8 and E9 Federal LP-390 C, II-H, Grades 1 and 2, Category 4 ISO 1872-PE, KHKN,45-D006 Telephone wire insulated with AXELERON™ CS K-3364 NT CPD, using sound commercial extrusion practices, should meet the following cable specifications: ICEA S-84-608 EN-50290-2-23 IEC 60708 DIN VDE 0819-103 BS 6234 type H03 NF C 32-060

Message

AXELERON™ CS K-3364 NT CPD is a high-molecular weight, high-density polyethylene insulation compound ("CPD") specifically formulated to provide excellent oxidative stability, toughness, and abrasion resistance. It provides superior long term aging performance, while providing excellent environmental and thermal stress-cracking resistance. In addition, AXELERON™ CS K-3364 NT CPD provides excellent processability for high-speed wire insulating extrusion processes.

AXELERON™ CS K-3364 NT CPD provides good performance for telephone insulation applications, primarily cable designs for aerial environments. AXELERON™ CS K-3364 NT CPD is optimized to meet major international age testing standards and specifications for both solid and foam/skin insulation use.

Specifications
AXELERON™ CS K-3364 NT CPD meets the following raw material specifications:

ASTM D 1248 Type III Category A-4, Grade E8 and E9

Federal LP-390 C, II-H, Grades 1 and 2, Category 4

ISO 1872-PE, KHKN,45-D006

Telephone wire insulated with AXELERON™ CS K-3364 NT CPD, using sound commercial extrusion practices, should meet the following cable specifications:

ICEA S-84-608

EN-50290-2-23

IEC 60708

DIN VDE 0819-103

BS 6234 type H03

NF C 32-060

General Information
Uses	Thin wall insulation Telephone insulator Wire and cable applications Solid insulation Communication wire insulation material
Agency Ratings	ASTM D 1248, III, Class A, Cat. 4, Grade E8 ASTM D 1248, III, Class A, Cat. 4, Grade E9 BS 6234 Type H03 EN 50290-2-23 FED L-P-390C, Type II, Class H, Category 4, Grade 1 ICEA S-84-608 IEC 60708 NF C 32-060
Forms	Particle

Physical	Nominal Value	Unit	Test Method
Density	0.947	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)	0.75	g/10 min	ASTM D1238
Environmental Stress-Cracking Resistance (100°C, 100% Igepal, F0)	> 48.0	hr	ASTM D1693

Mechanical	Nominal Value	Unit	Test Method
Tensile Strength	23.4	MPa	ASTM D638
Tensile Elongation (Break)	500	%	ASTM D638

Aging	Nominal Value	Unit	Test Method
Tensile strength retention- 48 hrs (100°C)	90	%	ASTM D638
Elongation retention rate- 48 hrs (100°C)	90	%	ASTM D638

Thermal	Nominal Value	Unit	Test Method
Heat resistant stress crack- F0	> 96	hr	ASTM D2951
Brittleness Temperature ¹	-76.0	°C	ASTM D746

Electrical	Nominal Value	Unit	Test Method
Volume Resistivity (23°C)	> 1.0E+15	ohms·cm	ASTM D257
Dielectric Constant ²(1 MHz)	2.32		ASTM D1531
Dissipation Factor (1 MHz)	6.0E-5		ASTM D1531

Extrusion	Nominal Value	Unit
Melt Temperature	218 - 260	°C

Extrusion instructions
AXELERON™ CS K-3364 NT CPD provides excellent surface finish and good output rates over a broad range of extrusion conditions. AXELERON™ CS K-3364 NT CPD is typically extruded at melt discharge temperatures ranging from 218-260°C (425-500°F) using conductor preheats ranging from 110-140°C (230-290°F). Specific extrusion conditions can be recommended only when the application, processing speed and processing equipment details are known.

Extrusion instructions

AXELERON™ CS K-3364 NT CPD provides excellent surface finish and good output rates over a broad range of extrusion conditions. AXELERON™ CS K-3364 NT CPD is typically extruded at melt discharge temperatures ranging from 218-260°C (425-500°F) using conductor preheats ranging from 110-140°C (230-290°F). Specific extrusion conditions can be recommended only when the application, processing speed and processing equipment details are known.

Note Message
1 .	F0
2 .	After 14 days Water Immersion at 23°C (73°F)

Resin Grade	Manufacturer	Category	Trademark
Queo™ 8201LA	Borealis AG	Plastomer	Queo™
SIMONA® PVC VS-1	SIMONA AMERICA, Inc.	PVC, Rigid	SIMONA®
CERTENE鈩?PHS-1	Muehlstein	PP Homopolymer	CERTENE™
Lustran庐 ABS 633	Styrolution	ABS	Lustran® ABS
ADENE® O07UFBG-00	A.D. Compound S.p.A.	PP Copolymer	ADENE®

Resin Grade

Manufacturer

Category:	HDPE , High Density Polyethylene Solid Insulation Compound
Manufacturer:	The Dow Chemical Company
Trademark:	AXELERON™
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	v06PkD_AXELERON-CS-K-3364-NT-CPD.pdf
PRICE:	Order Products email sales@su-jiao.com