Order Products : sales@su-jiao.com

NOVAPOL® TR-0535-UI(UIG)

Category:	LLDPE , Linear Low Density Polyethylene
Manufacturer:	NOVA Chemicals
Trademark:	NOVAPOL®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	scYigD_NOVAPOL-TR-0535-UI-UIG-.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

WECHAT

Message

NOVAPOL® TR-0535-UI(UIG) is a Linear Low Density Polyethylene material. It is available in North America for compression molding or rotational molding.

Important attributes of NOVAPOL® TR-0535-UI(UIG) are:

Antioxidant

Food Contact Acceptable

Good Stiffness

High ESCR (Stress Crack Resistant)

Impact Resistant

Typical applications include:

Food Contact Applications

Plumbing/Piping/Potable Water

Tanks

Consumer Goods

Marine Applications

General Information
Additive	Antioxidant UV Stabilizer
Features	Antioxidant Food Contact Acceptable General Purpose Good Stiffness High ESCR (Stress Crack Resist.) Low Temperature Impact Resistance Medium Density
Uses	Agricultural Tanks General Purpose Marine Applications Septic Tanks Toys
Agency Ratings	FDA 21 CFR 176.170(c), Table 2, Cond. D FDA 21 CFR 176.170(c), Table 2, Cond. E FDA 21 CFR 176.170(c), Table 2, Cond. F FDA 21 CFR 176.170(c), Table 2, Cond. G FDA 21 CFR 177.1520(c) 3.2a NSF 14 NSF 24 NSF 61
Forms	Pellets
Processing Method	Compression Molding Rotational Molding

Physical	Nominal Value	Unit	Test Method
Density	0.935	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)	5.0	g/10 min	ASTM D1238
Environmental Stress-Cracking Resistance
50°C, 10% Igepal, Compression Molded, F50	> 1000	hr	ASTM D1693B
50°C, 100% Igepal, Compression Molded, F50	> 1000	hr	ASTM D1693A

Mechanical	Nominal Value	Unit	Test Method
Tensile Strength ¹(Yield, 1.90 mm, Compression Molded)	17.5	MPa	ASTM D638
Tensile Elongation ²(Yield, 1.90 mm, Compression Molded)	12	%	ASTM D638
Flexural Modulus - 1% Secant (Compression Molded)	680	MPa	ASTM D790

Impact	Nominal Value	Unit	Test Method
ARM Impact - Rotational Molded			ARM
-40°C, 3.18 mm	67.0	J
-40°C, 6.35 mm	217	J

Thermal	Nominal Value	Unit	Test Method
Deflection Temperature Under Load			ASTM D648
0.45 MPa, Unannealed	58.0	°C
1.8 MPa, Unannealed	42.0	°C
Peak Melting Temperature	125	°C	ASTM E794

Note Message
1 .	Type IV, 51 mm/min
2 .	Type IV, 51 mm/min

Resin Grade	Manufacturer	Category	Trademark
SLOVALEN® PH 72 T 20	Plastcom	PP, Unspecified	SLOVALEN®
AMTOPP PM25	Inteplast Group	PP, Unspecified	AMTOPP
DIC.PPS FZ-3600-D5	DIC Corporation	PPS	DIC.PPS
Elastron® G G500.A60.N.ABS	Elastron USA, Inc.	SEBS	Elastron® G
LUVOCOM® 1105-9182/XTF	LEHVOSS Group	PEEK	LUVOCOM®