Order Products : sales@su-jiao.com
Versollan™ RU 2205-1
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | PolyOne Corporation |
| Trademark: | Versollan™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | sILfng_Versollan-RU-2205-1.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Versollan™RU 2205-1 is the first product of a new generation of high-performance polyurethane (TPU) alloys that can be molded by injection molding. It can produce a rubber-like feel and appearance and shorten the cycle period, while having the performance of TPU. New Products. Commercial norms have not yet been established.
|
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| RoHS Compliance |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.16 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) | ASTM D1238 | ||
| 190°C/2.16 kg | 7.0 | g/10 min | ASTM D1238 |
| 200°C/5.0 kg | 67 | g/10 min | ASTM D1238 |
| Molding Shrinkage - Flow | 1.0 - 1.5 | % | ASTM D955 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 10 sec) | 65 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress 1 | ASTM D412 | ||
| 100% strain, 23°C 2 | 2.62 | MPa | ASTM D412 |
| 300% strain, 23°C 3 | 4.21 | MPa | ASTM D412 |
| Tensile Strength (Break, 23°C) | 13.8 | MPa | ASTM D412 |
| Tensile Elongation (Break, 23°C) | 710 | % | ASTM D412 |
| Tear Strength | 47.3 | kN/m | ASTM D624 |
| Compression Set (23°C, 22 hr) | 34 | % | ASTM D395B |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Brittleness Temperature 4 | -67.0 | °C | ASTM D746 |
| Flammability | Nominal Value | Test Method | |
|---|---|---|---|
| Flame Rating 5(1.50 mm) | HB | UL 94 |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Apparent Viscosity (200°C, 11200 sec^-1) | 14.1 | Pa·s | ASTM D3835 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 51.7 - 54.4 | °C | |
| Drying Time | 3.0 - 4.0 | hr | |
| Suggested Max Moisture | < 0.030 | % | |
| Suggested Max Regrind | 20 | % | |
| Rear Temperature | 168 - 188 | °C | |
| Middle Temperature | 179 - 199 | °C | |
| Front Temperature | 191 - 210 | °C | |
| Nozzle Temperature | 191 - 216 | °C | |
| Processing (Melt) Temp | 188 - 210 | °C | |
| Mold Temperature | 21.1 - 32.2 | °C | |
| Back Pressure | 0.00 - 0.862 | MPa | |
| Screw Speed | 75 - 125 | rpm |
| Injection instructions |
|---|
| 或聚醚型聚氨酯为基础的色母料最适合 Versollan™ RU 2205-1 着色。典型的母料浓度为 50:1 到 25:1 - 要最大限度减少对硬度的影响，用量应该尽可能低。若使用 GLS 可供的预着色复合材料，则可达到较好的配色一致性。不推荐使用以聚丙烯 (PP) 为基础的色母料，因为其对 TPE 与基体之间的粘接会有显著影响。不应采用以 TPE 为基础的色母料。色母料是否适用，应由用户通过试验来最终确定。在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。Versollan™ RU 2205-1 可利用高达 20% 的回收料同时其性能所受影响却极小，但该回收料必须是未受到污染的。为了最大限度地减小模塑期间其性能所受的影响，熔体温度应维持得尽可能低。回收料的有效性应由用户最终确定。Versollan™ RU 2205-1 不应在机筒内闲置过长时间（5 分钟以上）。建议露点：-40°F注射速度：0.5 - 2 英寸/秒第一阶段 - 提升压力：300 - 700 psi第二阶段 - 保持压力：30% 的升压保持时间（厚部件）：4 - 10 秒保持时间（薄部件）：1 - 3 秒 |
| Note Message | |
|---|---|
| 1 . | 2 hours |
| 2 . | Mouth die c |
| 3 . | C mould |
| 4 . | Thickness = 1.91mmConditioned for 40hrs at 23C at 50% RH |
| 5 . | 1.5mm for US and China; 3.0mm for Canada. |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Spartech PS SP-2010 | Spartech Plastics | PS (HIPS) | Spartech |
| ADMER™ NF528E | Mitsui Chemicals Europe GmbH | PE, Unspecified | ADMER™ |
| GERMAMID 6.6 ST SCHWARZ | Kunststoff-Kontor-Hamburg GmbH | Nylon 66 | GERMAMID |
| KOPLA PA6 KNR1031 | KOPLA Co., Ltd. | Nylon 6 | KOPLA PA6 |
| PIVINEL™ 108-0 | HELLENIC CABLES S.A. | PVC, Unspecified | PIVINEL™ |
