Order Products : sales@su-jiao.com
CONAPOXY® AD-10
| Category: | Epoxy , Epoxy; Epoxide |
| Manufacturer: | Cytec Industries Inc. |
| Trademark: | CONAPOXY® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | r3V7Ds_CONAPOXY-AD-10.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
CONAPOXY AD-10 is a unique single-component epoxy that may be used as a structural adhesive or miniature electronic potting compound. The heat-cure formulation was designed for rapid cure at temperatures as low as 93°C (200°F), yet it exhibits good storage life at room temperature. Good dielectric properties and thermal stability make this epoxy ideal for electrical applications up to 150°C (302°F). This single-component epoxy may be used to bond to most metals, ceramics, and plastics and it is chemically resistant to many acids and bases. Specific applications include bonding and/or sealing magnet and speaker assemblies, batteries, filters, end cap filling, structural materials, miniature potting and staking. CONAPOXY AD-10 is typically used as an adhesive and should not be used in excess of 1/8 " thickness. This epoxy eliminates the possibility of human error when mixing two-component systems. By using CONAPOXY AD-10 the manufacturer will save time, ensure quality and reduce scrap. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Appearance |
|
| Physical | Nominal Value | Unit | |
|---|---|---|---|
| Specific Gravity | 1.27 | g/cm³ | |
| Solids Content | 100 | % | |
| Viscosity (25°C) | Thixotropic Non-Flow |
| Additional Information | Nominal Value | Unit | |
|---|---|---|---|
| Operating Temperature | -55 to 150 | °C |
| Electrical | Nominal Value | Unit | |
|---|---|---|---|
| Dielectric Strength | > 15 | kV/mm | |
| Dielectric Constant (25°C, 1 kHz) | 4.00 | ||
| Dissipation Factor (25°C, 1 kHz) | 6.0E-3 |
| Thermoset | Nominal Value | Unit | |
|---|---|---|---|
| Shelf Life | |||
| 5°C | 35 | wk | |
| 25°C | 17 | wk | |
| Demold Time | |||
| 93°C | 120 to 150 | min | |
| 107°C | 65 to 80 | min | |
| 121°C | 30 to 40 | min | |
| 135°C | 12 to 20 | min | |
| 149°C | 8.0 to 12 | min | |
| 162°C | 5.0 to 8.0 | min | |
| 204°C | 2.0 to 4.0 | min |
| Cured Properties | Nominal Value | Unit | |
|---|---|---|---|
| Lap Shear Strength 1 | 20.7 | MPa |
| Note Message | |
|---|---|
| 1 . | AL/AL |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| POLYMAN® (ABS) LP 125/2 GL | A. Schulman Europe | ABS | POLYMAN® |
| RTP 4082 A | RTP Company | PPA | RTP |
| Purell PE 3020 K | LyondellBasell Industries | LDPE | Purell |
| Andur 80-5AP/Curene® 280 | Anderson Development Company | PUR-Ether/TDI | Andur |
| Ebalta GM 956 / Comp. A+B | Ebalta Kunststoff GmbH | PUR, Unspecified | Ebalta |
