Order Products : sales@su-jiao.com
Polybutene-1 PB 8340M
| Category: | PB , Polybutylene |
| Manufacturer: | LyondellBasell Industries |
| Trademark: | Polybutene-1 |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | pMNi3E_Polybutene-1-PB-8340M.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Polybutene-1 grade PB 8340M is a random copolymer of butene-1 with low ethylene content. In blends with PE polymers, it forms a separate, but well-dispersed phase. Its primary use is as a minority blend component in the seal layer of easy-opening packaging films, produced by cast film extrusion. A typical PE blend partner for PB 8340M could be any ethylene homo-or copolymer in the melt index range of 2.0 to 8.0 g/10min. Polybutene-1 is also highly compatible with polypropylene due to its similar molecular structure, and it can be used to modify PP sealing behavior or mechanical properties such as impact strength. PB-1 crystallizes slowly and is very shear sensitive in its flow behavior. Food law compliance information about this product can be found in separate product documentation. This product is not intended for use in medical and pharmaceutical applications. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 0.911 | g/cm³ | ISO 1183 |
| Melt Mass-Flow Rate (MFR) | ISO 1133 | ||
| 190°C/10.0 kg | 100 | g/10 min | ISO 1133 |
| 190°C/2.16 kg | 4.0 | g/10 min | ISO 1133 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress (Break) | 30.0 | MPa | ISO 527-2 |
| Tensile Strain (Break) | 300 | % | ISO 527-2 |
| Flexural Modulus | 270 | MPa | ISO 178 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Melting Temperature (DSC) | DSC | ||
| -- 1 | 97.0 | °C | DSC |
| -- 2 | 113 | °C | DSC |
| Additional Information |
|---|
| Tm2 corresponds with the melting point of crystalline form 2 which is measured immediately after solidification. Tm2 corresponds with the melting point available for each batch on the Certificate of Analysis (COA). |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Melt Temperature | 180 - 200 | °C |
| Extrusion instructions |
|---|
| Recommended processing temperatures: 180°C to 200°C. In cases were higher temperatures are required please contact your appropriate technical contact for support. |
| Note Message | |
|---|---|
| 1 . | Tm2 |
| 2 . | Tm1 |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| TUFNYL® RXXIC INDICA GREY | SRF Ltd. | Nylon 66 | TUFNYL® |
| CelloTherm™ P400 | Innovia Films Ltd. | CA | CelloTherm™ |
| LUVOCOM® 1-8068/GY VP | Lehmann & Voss & Co. | Nylon 66 | LUVOCOM® |
| EcoHumer BFX103 | WooSung Chemical Co., Ltd. | PBAT | EcoHumer |
| Romiloy® 6020 UV | ROMIRA GmbH | ASA+PC | Romiloy® |
