Order Products : sales@su-jiao.com
Monprene® OM-10230
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | Teknor Apex Company |
| Trademark: | Monprene® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | knzKBh_Monprene-OM-10230.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Monprene®OM-10230 is a thermoplastic elastomer (TPE) material,. This product is available in North America, Africa and the Middle East, Latin America, Europe or Asia Pacific. The processing method is extrusion or injection molding. Typical application areas include:
|
| General Information | |
|---|---|
| Uses |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 0.948 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) | ASTM D1238 | ||
| 190°C/2.16 kg | 20 | g/10 min | ASTM D1238 |
| 230°C/2.16 kg | 40 | g/10 min | ASTM D1238 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness | ASTM D2240 | ||
| Shaw A | 30 | ASTM D2240 | |
| Shaw A, 5 seconds | 27 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength (Break) | 3.60 | MPa | ASTM D412 |
| Tensile Elongation (Break) | 560 | % | ASTM D412 |
| Compression Set (23°C) | 25 | % | ASTM D395 |
| Additional Information | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Adhesion to ABS | |||
| Adhesion to PC - Cohesive Failure 1 | 2.5 | kN/m | ASTM D429 |
| Adhesion to PC/ABS | |||
| Adhesion to PMMA - Cohesive Failure 2 | 3.2 | kN/m |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 60.0 | °C | |
| Drying Time | 2.0 - 4.0 | hr | |
| Rear Temperature | 138 - 188 | °C | |
| Middle Temperature | 154 - 199 | °C | |
| Front Temperature | 154 - 216 | °C | |
| Nozzle Temperature | 154 - 221 | °C | |
| Processing (Melt) Temp | 166 - 221 | °C | |
| Mold Temperature | 10.0 - 32.2 | °C | |
| Injection Pressure | 1.38 - 5.52 | MPa | |
| Back Pressure | 0.172 - 0.862 | MPa | |
| Screw Speed | 50 - 100 | rpm | |
| Cushion | 3.81 - 25.4 | mm |
| Injection instructions |
|---|
| 潮湿会使材料降解。建议进行干燥处理。可以把材料放入除湿干燥机，在140°F的温度下干燥2-4小时。 |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Cylinder Zone 1 Temp. | 138 - 149 | °C | |
| Cylinder Zone 2 Temp. | 149 - 160 | °C | |
| Cylinder Zone 3 Temp. | 160 - 182 | °C | |
| Cylinder Zone 5 Temp. | 171 - 193 | °C | |
| Die Temperature | 182 - 204 | °C |
| Note Message | |
|---|---|
| 1 . | 180 Degree Peel Test |
| 2 . | 180 Degree Peel Test |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Topilene® J440 | Hyosung Corporation | PP Impact Copolymer | Topilene® |
| Adell Polyamide AW-38 | Adell Plastics, Inc. | Nylon 66 | Adell Polyamide |
| KOPA® KN133CT | Kolon Plastics, Inc. | Nylon 6 | KOPA® |
| ImerPlast™ 20 | Imerys Minerals | Polyolefin, Unspecified | ImerPlast™ |
| KOPA® KN133G30 | Kolon Plastics, Inc. | Nylon 6 | KOPA® |
