LUVOCOM® 3-9064 Datasheet,Nylon 6,LEHVOSS Group-SHANGHAI SUSHENG

Message
LUVOCOM®3-9064 is a polyamide 6 (nylon 6) material, and the filler is glass fiber reinforced material. This product is available in North America, Africa and the Middle East, Latin America, Europe or Asia Pacific,. LUVOCOM®The main features of 3-9064 are: Antistatic anti-warping Good stiffness Typical application areas include: engineering/industrial accessories textile/fiber Automotive Industry

General Information
Filler / Reinforcement	Glass fiber reinforced material
Additive	Antistatic property
Features	Low warpage Rigid, good Antistatic property Good liquidity Good strength
Uses	Thin wall parts Textile applications Engineering accessories Application in Automobile Field
Appearance	Black

Physical	Nominal Value	Unit	Test Method
Density	1.55	g/cm³	ISO 1183
Melt Mass-Flow Rate (MFR) (250°C/5.0 kg)	10	g/10 min	ISO 1133
Molding Shrinkage	0.30 - 0.60	%	DIN 16901
Water Absorption (23°C, 24 hr)	< 1.0	%

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus	9000	MPa	ISO 527-2
Tensile Stress (Break)	140	MPa	ISO 527-2
Tensile Strain (Yield)	2.5	%	ISO 527-2
Flexural Modulus	7500	MPa	ISO 178
Flexural Stress	195	MPa	ISO 178

Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength (23°C)	5.0	kJ/m²	ISO 179/1eA
Charpy Unnotched Impact Strength (23°C)	50	kJ/m²	ISO 179/1eU

Thermal	Nominal Value	Unit	Test Method
Continuous Use Temperature	90.0	°C	UL 746B
Maximum operating temperature- Short Term	130	°C

Electrical	Nominal Value	Unit	Test Method
Insulation Resistance	1.0E+6 - 1.0E+9	ohms	IEC 60167

Injection	Nominal Value	Unit
Drying Temperature
Hot air dryer, A	75	°C
Hot air dryer, B	105	°C
Drying Time
Hot air dryer, A	10 - 16	hr
Hot air dryer, B	4.0 - 6.0	hr
Rear Temperature	250 - 270	°C
Middle Temperature	270 - 290	°C
Front Temperature	280 - 300	°C
Nozzle Temperature	270 - 280	°C
Processing (Melt) Temp	270	°C
Mold Temperature	70 - 110	°C

Injection instructions
General In general LUVOCOM® can be processed on conventional injection moulding machines while observing the usual technical guidelines. Any added fibrous materials or fillers may have an abrasive effect. In this case the cylinder and screw should be protected against wear as is usual in the processing of reinforced thermoplastic materials. Lengthy dwell times for the melts in the cylinder should be avoided. Lower the temperatures during interruptions! Predrying (optional) It is advisable to predry the granulate with a suitable dryer immediately before processing. The granulate may absorb moisture from the air. Delivery Form & Storage Unless indicated otherwise, the material is delivered as 3mm-long pellets in sealed bags on pallets. Preferably storage should be effected in dry and normally temperatured rooms Additional Information During processing the moisture level should not exceed 0.1%, otherwise molecular degradation and surface defects (e.g. smearing) may occur. As the material absorbs water rapidly, originally sealed containers should only be opened immediately before processing. Excessively high predrying temperatures may cause discoloration. The processing notes provided merely represent a recommendation for general use. Due to the large variety of machines, geometries and volumes of parts, etc., it may be necessary to employ different settings according to the specific application. Please contact us for further information.

Injection instructions

General In general LUVOCOM® can be processed on conventional injection moulding machines while observing the usual technical guidelines. Any added fibrous materials or fillers may have an abrasive effect. In this case the cylinder and screw should be protected against wear as is usual in the processing of reinforced thermoplastic materials. Lengthy dwell times for the melts in the cylinder should be avoided. Lower the temperatures during interruptions! Predrying (optional) It is advisable to predry the granulate with a suitable dryer immediately before processing. The granulate may absorb moisture from the air. Delivery Form & Storage Unless indicated otherwise, the material is delivered as 3mm-long pellets in sealed bags on pallets. Preferably storage should be effected in dry and normally temperatured rooms Additional Information During processing the moisture level should not exceed 0.1%, otherwise molecular degradation and surface defects (e.g. smearing) may occur. As the material absorbs water rapidly, originally sealed containers should only be opened immediately before processing. Excessively high predrying temperatures may cause discoloration. The processing notes provided merely represent a recommendation for general use. Due to the large variety of machines, geometries and volumes of parts, etc., it may be necessary to employ different settings according to the specific application. Please contact us for further information.

Category:	Nylon 6 , Polyamide 6
Manufacturer:	LEHVOSS Group
Trademark:	LUVOCOM®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	f7UqFB_LUVOCOM39064.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
SABIC® LLDPE 726Q	Saudi Basic Industries Corporation (SABIC)	LLDPE	SABIC® LLDPE
Trilliant™ HC HC9820-0030 RS Natural	PolyOne Corporation	PEEK	Trilliant™ HC
Elastron® G G401.A55.N	Elastron USA, Inc.	SEBS	Elastron® G
OTECH TPE OTO8099 - Profile	OTECH Corporation	TPE	OTECH TPE
SQUARE® LSR1966-34A/B	Shenzhen SQUARE Silicone Co., Ltd.	Silicone Rubber, LSR	SQUARE®