Order Products : sales@su-jiao.com
FireCon™ CPE 1240 UV RoHS NATURAL
| Category: | CPE , Chlorinated Polyethylene |
| Manufacturer: | PolyOne Corporation |
| Trademark: | FireCon™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | elsiBW_FireCon-CPE-1240-UV-RoHS-NATURAL.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| The filled flexible thermoplastic CPE sheath compound material is ideal for low-voltage power and control cables. Wire and cable manufacturers use the material for thermoplastic extrusion processing without investing in continuous vulcanization (CV) equipment. CPE 30-11 REV 2 is especially suitable for cables with larger diameters. The composite material passed the heat/seismic test. This test requires that the cable can withstand bending and twisting without cracking or compression. Good humidity characteristics, oil characteristics and electrical characteristics. The material can be used as power and control cables for fossil fuel power plants and thermal power plants. |
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| RoHS Compliance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.32 | g/cm³ | ASTM D792 |
| Appearance | Particles/cubes | ASTM D2090 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore D, 10 sec) | 48 | ASTM D2240 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus 1 | 8.96 | MPa | ASTM D638 |
| Tensile Strength 2(Break) | 16.5 | MPa | ASTM D638 |
| Tensile Elongation 3(Break) | 500 | % | ASTM D638 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Tensile Strength (70°C, 24 hr, in IRM 902 oil) | 60 | % | IEC 60811-2-1 |
| Change in Tensile Strain at Break (70°C, 24 hr, in IRM 902 oil) | 88 | % | IEC 60811-2-1 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Oxygen Index (1.91 mm) | 33 | % | ASTM D2863 |
| Additional Information |
|---|
| 注释：天然- 根据螺旋设计不同处于290°-330°F之间的典型加工温度。请联系技术服务部，获取特定设备的推荐。注释：推荐在175°-185°F下预干燥4小时。注释：模制厚板的典型属性（0.075"）；不能视为技术规格。 |
| Note Message | |
|---|---|
| 1 . | Type 4, 510mm/min |
| 2 . | Type 4, 510mm/min |
| 3 . | Type 4, 510mm/min |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Raditer® B N100 | Radici Plastics | PBT | Raditer® |
| WPP PP PPC3GF1.5-Natural | Washington Penn Plastic Co. Inc. | PP Impact Copolymer | WPP PP |
| Hostalen PP H5416 K | LyondellBasell Industries | PP Random Copolymer | Hostalen |
| KOPLA PA66 KUG1330BK | KOPLA Co., Ltd. | Nylon 66 | KOPLA PA66 |
| PIVINEL™ 118F-LF | HELLENIC CABLES S.A. | PVC, Unspecified | PIVINEL™ |
