Order Products : sales@su-jiao.com
CONATHANE庐 EN-16
| Category: | PUR, Unspecified , Polyurethane |
| Manufacturer: | Cytec Industries Inc. |
| Trademark: | CONATHANE® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | d11hS9_CONATHANE-EN-16.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
CONATHANE EN-16 is a two-component, unfilled urethane system formulated to meet the requirements of MIL-M-24041C: PRO 20 Amendment. It is a polyether based, non-MBOCA polyurethane resin system primarily intended for use as a molding, encapsulating, and potting compound for harness breakouts, watertight electrical connectors, cables, cable end seals, printed circuitry, and other electrical components. The system also has use in the casting or molding of mechanical parts and as a lining material for pumps, chutes, and conveyors where outstanding abrasion resistance is required. CONATHANE EN-16 may be cured at room or elevated temperatures. CONATHANE EN-16, when fully cured, is a tough , cold-flow resistant elastomer that has good resistance to oils, gasoline, JP-4 fuel, water, and sea water, and also provides outstanding protection against corrosion or contamination. The system is funginert when tested in accordance with MIL-I-46058C and ASTM G-21 and meets or exceeds all of the requirements of MIL-M-24041C: PRO 20 Amendment. Three primers have been developed for use in bonding EN-16 to metals, neoprene, and polyvinyl chloride during the curing process. CONAP® AD-1146 is recommended for metals, CONAP® PR-1167 for neoprene, and CONAP® AD-1161 for polyvinyl chloride. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Appearance |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | |
|---|---|---|---|
| Specific Gravity 1 | 1.06 | g/cm³ | |
| Water Absorption (24 hr) | 2.6 | % |
| Elastomers | Nominal Value | Unit | |
|---|---|---|---|
| Tensile Stress | |||
| 100% Strain | 4.92 | MPa | |
| 300% Strain | 8.96 | MPa | |
| Tensile Strength | 29.1 | MPa | |
| Tensile Elongation (Break) | 510 | % | |
| Tear Strength | 73.2 | kN/m | |
| Compression Set | 44 | % |
| Electrical | Nominal Value | Unit | |
|---|---|---|---|
| Surface Resistivity | 1.7E+14 | ohms | |
| Volume Resistivity (25°C) | 1.4E+12 | ohms·cm | |
| Dielectric Strength (1.59 mm) | 19 | kV/mm | |
| Dielectric Constant (25°C, 1 kHz) | 6.38 | ||
| Dissipation Factor (25°C, 1 kHz) | 0.032 | ||
| Insulation Resistance (25°C) | 1.5E+11 | ohms |
| Thermoset | Nominal Value | Unit | |
|---|---|---|---|
| Thermoset Components | |||
| Hardener | Mix Ratio by Weight: 25 | ||
| Resin | Mix Ratio by Weight: 100 | ||
| Thermoset Mix Viscosity (25°C) | 4000 | cP |
| Note Message | |
|---|---|
| 1 . | Hardener |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| VENYL SEG138 - 7963 | AD majoris | Nylon 6 | VENYL |
| TOTAL Polypropylene Lumicene® MR 2002 | TOTAL Refining & Chemicals | PP Homopolymer | TOTAL Polypropylene |
| Jam PE 26560 | Jam Petrochemical Company | LLDPE | Jam PE |
| LITEN BB 38 | UNIPETROL RPA | PE Copolymer | LITEN |
| OP - PC - Unfilled 912-FDA | Oxford Polymers | PC | OP - PC - Unfilled |
