Telcar® TL-2934N Datasheet,TPE,Teknor Apex Company-SHANGHAI SUSHENG

Message
Telcar TL-2934N is a high performance UL V-0 flame retardant thermoplastic elastomer designed for electrical applications requiring flexibility over a wide temperature range. Telcar TL-2934N is a high hardness, high density, low flow grade that is UV stabilized and RoHS compliant. This UL listed grade is easily colorable and is suitable for both injection molding and extrusion.

General Information
Features	High specific gravity High tensile strength High density Good UV resistance Good heat aging resistance Good coloring Low liquidity Halogenated Sunlight resistance, 720 hours General brominated Extended tensile rate High hardness Flame retardancy
Uses	Underground cable Cable sheath Electrical wire sheath material Electrical conductor insulation material Wire and cable applications Wire sheath Industrial cable insulation material Connector cord sheath ribbon Rubber substitution Terminal cable sheath material
Agency Ratings	UL 94
RoHS Compliance	RoHS compliance
Appearance	Black Natural color
Forms	Particle
Processing Method	Extrusion Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.30	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)	0.30	g/10 min	ASTM D1238

Hardness	Nominal Value	Test Method
Durometer Hardness		ASTM D2240
Shore A, 1 second, injection molding	90	ASTM D2240
Shore A, 5 seconds, injection molding	88	ASTM D2240

Elastomers	Nominal Value	Unit	Test Method
Tensile Strength (Break)	12.4	MPa	ASTM D412
Tensile Elongation (Break)	600	%	ASTM D412
Tear Strength ¹			ASTM D624
Transverse flow : 23°C	39.4	kN/m	ASTM D624
Flow : 23°C	44.0	kN/m	ASTM D624
Compression Set (125°C, 70 hr)	14	%	ASTM D395

Aging	Nominal Value	Unit	Test Method
Change in Tensile Strength in Air (158°C, 168 hr)	27	%	ASTM D573
Change in Ultimate Elongation in Air (158°C, 168 hr)	-7.0	%	ASTM D573
Change in Tensile Strength (60°C, 168 hr, in IRM 902 Oil)	-4.0	%	ASTM D471
Change in Ultimate Elongation (60°C, 168 hr, in IRM 902 Oil)	-4.0	%	ASTM D471

Thermal	Nominal Value	Unit	Test Method
Brittleness Temperature	-50.0	°C	ASTM D746

Electrical	Nominal Value	Unit	Test Method
Volume Resistivity			ASTM D257
23°C	1.7E+16	ohms·cm	ASTM D257
50°C	5.3E+14	ohms·cm	ASTM D257
Dielectric Strength (23°C)	43	kV/mm	ASTM D149
Dielectric Constant			ASTM D150
23°C, 1 MHz	2.53		ASTM D150
23°C, 1 kHz	2.61		ASTM D150
Dissipation Factor			ASTM D150
23°C, 1 MHz	5.8E-3		ASTM D150
23°C, 1 kHz	5.8E-3		ASTM D150

Flammability	Nominal Value	Unit	Test Method
Flame Rating (1.5 mm, NT, BK, WT)	V-0		UL 94
Oxygen Index	28	%	ASTM D2863

Legal statement
The information and recommendations contained in this bulletin are, to the best of our knowledge, accurate and reliable but no guarantee of their accuracy is made. All products are sold upon condition that purchasers shall make their own tests to determine the suitability of such products for their particular purposes and uses and purchaser assumes all risks and liability for the results of use of the products, including use in accordance with seller's recommendations. Nothing in this bulletin constitutes permission or a recommendation to practice or use any invention covered by any patent owned by this company or others. There is no warranty of merchantability and there are no other warranties for the products described. For detailed Product Stewardship information, please contact us. Any product of Teknor Apex, including product names, shall not be used or tested in medical or food contact applications without the prior written acknowledgement of Teknor Apex as to the intended use. Please note that some products may not be available in one or more countries.

Legal statement

The information and recommendations contained in this bulletin are, to the best of our knowledge, accurate and reliable but no guarantee of their accuracy is made. All products are sold upon condition that purchasers shall make their own tests to determine the suitability of such products for their particular purposes and uses and purchaser assumes all risks and liability for the results of use of the products, including use in accordance with seller's recommendations. Nothing in this bulletin constitutes permission or a recommendation to practice or use any invention covered by any patent owned by this company or others. There is no warranty of merchantability and there are no other warranties for the products described. For detailed Product Stewardship information, please contact us. Any product of Teknor Apex, including product names, shall not be used or tested in medical or food contact applications without the prior written acknowledgement of Teknor Apex as to the intended use. Please note that some products may not be available in one or more countries.

Injection	Nominal Value	Unit
Rear Temperature	199 - 216	°C
Middle Temperature	213 - 221	°C
Front Temperature	221 - 227	°C
Nozzle Temperature	221 - 229	°C
Processing (Melt) Temp	221 - 229	°C
Mold Temperature	25 - 66	°C
Injection Pressure	1.38 - 6.89	MPa
Injection Rate	Moderate-Fast
Back Pressure	0.172 - 0.345	MPa
Screw Speed	50 - 100	rpm
Cushion	3.81 - 25.4	mm

Injection instructions
Drying is not necessary. However, if moisture is a problem, dry the pellets for 2 to 4 hours at 150°F (65°C).

Extrusion	Nominal Value	Unit
Cylinder Zone 1 Temp.	193 - 210	°C
Cylinder Zone 2 Temp.	199 - 216	°C
Cylinder Zone 3 Temp.	213 - 221	°C
Cylinder Zone 4 Temp.	213 - 221	°C
Cylinder Zone 5 Temp.	221 - 227	°C
Die Temperature	221 - 229	°C

Extrusion instructions
Screw Speed: 30 to 100 rpm

Note Message
1 .	C mold, 510mm/min

Category:	TPE , Thermoplastic Elastomer
Manufacturer:	Teknor Apex Company
Trademark:	Telcar®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	bb92Gu_TelcarTL2934N.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
Stanyl® ForTii™ F31	DSM Engineering Plastics	Nylon 4T	Stanyl® ForTii™
4MID® 9B22160	4Plas	Nylon 6	4MID®
Adflex KS311P	LyondellBasell Industries	Polyolefin, Unspecified	Adflex
Arnitel® EM631	DSM Engineering Plastics	TPC-ET	Arnitel®
DIAMALOY ABSPC 7801	Network Polymers, Inc.	PC+ABS	DIAMALOY ABSPC