Order Products : sales@su-jiao.com
DuraGrip® DGR 6160BK
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | Advanced Polymer Alloys |
| Trademark: | DuraGrip® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | bRayuZ_DuraGrip-DGR-6160BK.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| DuraGrip® 6160BK is designed to be a special purpose Melt Processible Elastomer (MPE) that is easy to use in injection molding and extrusion processes. DGR 6160BK has an excellent soft touch feel and will Bond to Nylon, ABS, PC, PC/ABS. DuraGrip® 6100 series is hygroscopic and requires drying prior to use. |
| General Information | |
|---|---|
| Features |
|
| Agency Ratings |
|
| RoHS Compliance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.07 | g/cm³ | ASTM D792, ISO 1183 |
| Molding Shrinkage | |||
| Flow : 1.59mm | 1.6 | % | ASTM D955 |
| Flow : 3.18mm | 1.5 | % | ASTM D955 |
| Transverse flow : 1.59mm | 0.0 | % | ASTM D955 |
| Transverse flow : 3.18mm | 0.50 | % | ASTM D955 |
| Vertical flow direction : 1.59mm | 0.0 | % | ISO 294-4 |
| Flow direction : 1.59mm | 1.6 | % | ISO 294-4 |
| Vertical flow direction : 3.18mm | 0.50 | % | ISO 294-4 |
| Flow direction : 3.18mm | 1.5 | % | ISO 294-4 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 5 sec) | 58 | ASTM D2240, ISO 868 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Taber Abrasion Resistance (1000 Cycles, 1.0E 6g, CS-17 wheel) | 189 | mg | ASTM D1044 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Set (100% Strain) | 4 | % | ASTM D412 |
| Tensile Stress | |||
| 100% strain | 2.21 | MPa | ASTM D412 |
| 100% strain, 23°C | 2.21 | MPa | ISO 37 |
| Tensile Strength (Yield, 23°C) | 6.62 | MPa | ASTM D412, ISO 37 |
| Tensile Elongation | |||
| Fracture | 350 | % | ASTM D412 |
| Fracture, 23°C | 350 | % | ISO 37 |
| Tear Strength 1(24°C) | 29.4 | kN/m | ASTM D624 |
| Compression Set | ASTM D395B, ISO 815 | ||
| 24°C, 22 hr | 21 | % | ASTM D395B, ISO 815 |
| 70°C, 22 hr | 82 | % | ASTM D395B, ISO 815 |
| 100°C, 22 hr | 91 | % | ASTM D395B, ISO 815 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Change in Tensile Strength in Air | |||
| 70°C, 168 hr | 11 | % | ASTM D573, ISO 188 |
| 100% strain, 70°C, 168 hr | 2.0 | % | ASTM D573 |
| 100°C, 168 hr | 40 | % | ASTM D573, ISO 188 |
| 100% strain, 100°C, 168 hr | -5.0 | % | ASTM D573 |
| 100% strain 70°C, 168 hr | 2.0 | % | ISO 188 |
| 100% strain 100°C, 168 hr | -5.0 | % | ISO 188 |
| Change in Ultimate Elongation in Air | ASTM D573 | ||
| 70°C, 168 hr | 4.0 | % | ASTM D573 |
| 100°C, 168 hr | 18 | % | ASTM D573 |
| Change in Tensile Strain at Break | ISO 1817 | ||
| 70°C, 168 hr | 4.0 | % | ISO 1817 |
| 100°C, 168 hr | 18 | % | ISO 1817 |
| Change in Volume | |||
| 24°C, 168 hr, in reference fuel B | 52 | % | ASTM D471 |
| 70°C, 168 hr, ASTM Standard Oil (No. 1) | 12 | % | ASTM D471 |
| 70°C, 168 hr, in IRM 903 oil | 74 | % | ASTM D471 |
| 70°C, 168 hr, in water | 2.0 | % | ASTM D471, ISO 1817 |
| 24°C, 168 hr, in reference fuel B | 52 | % | ISO 1817 |
| 70°C, 168 hr, in ASTM #1 oil | 12 | % | ISO 1817 |
| 70°C, 168 hr, in IRM 903 oil | 74 | % | ISO 1817 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Brittleness Temperature | -65.0 | °C | ASTM D746, ISO 812 |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Melt Viscosity (190°C, 300 sec^-1) | 354 | Pa·s | ASTM D3835 |
| Additional Information |
|---|
| The value listed as Density -Specific Gravity, ASTM D792, was tested in accordance with ASTM D471.The value listed as Density, ISO 1183, was tested in accordance with ISO 2781. |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 65.6 | °C | |
| Drying Time | 3.0 | hr | |
| Suggested Max Regrind | 25 | % | |
| Rear Temperature | 204 - 221 | °C | |
| Middle Temperature | 216 - 227 | °C | |
| Front Temperature | 227 - 238 | °C | |
| Nozzle Temperature | 227 - 249 | °C | |
| Processing (Melt) Temp | 227 - 254 | °C | |
| Mold Temperature | 43.3 - 54.4 | °C | |
| Injection Pressure | 2.76 - 5.52 | MPa | |
| Screw Speed | 50 - 150 | rpm |
| Injection instructions |
|---|
| DuraGrip® is not hygroscopic, under normal conditions does not require drying. Dry in a desiccant dryer if porosity is observed.Injection Speed: 1 to 3 in³/secInjection Time (1st Stage/Boost): 0.5 to 4 secSecond Stage Pressure: 300 to 500 psiSecond Stage Time: 3 to 10 secCooling Time: 10 to 25 secBack Pressure: 25 to 75 % |
| Note Message | |
|---|---|
| 1 . | C mould |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| VENYL SG308 - 3121 | AD majoris | Nylon 6 | VENYL |
| NYLOY® MC-0020N | Nytex Composites Co., Ltd. | Nylon 66 | NYLOY® |
| Evoprene™ Super G 934 | AlphaGary | SEBS | Evoprene™ Super G |
| ISOTHANE® 1090A | Great Eastern Resins Industrial Co Ltd (GRECO) | TPU-Polyester | ISOTHANE® |
| Kinta NB6615G | Kinta Technology (Hong Kong) Co., Ltd. | Nylon 66 | Kinta |
