Order Products : sales@su-jiao.com

Crastin® SK609 NC010

Category:	PBT , THERMOPLASTIC POLYESTER RESIN
Manufacturer:	DuPont Performance Polymers
Trademark:	Crastin®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	anppTI_CrastinSK609NC010.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

WECHAT

Message
50% Glass Reinforced Polybutylene Terephthalate

General Information
Filler / Reinforcement	Glass fiber reinforced material, 50% filler by weight
Additive	demoulding
RoHS Compliance	Contact manufacturer
Forms	Particle
Processing Method	Injection molding
Multi-Point Data	Creep Modulus vs. Time (ISO 11403-1) Isochronous Stress vs. Strain (ISO 11403-1) Isothermal Stress vs. Strain (ISO 11403-1) Secant Modulus vs. Strain (ISO 11403-1) Shear Modulus vs. Temperature, Dynamic (ISO 11403-1) Shear Stress vs. Shear Rate (ISO 11403-1) Viscosity vs. Shear Rate (ISO 11403-2)
Part Marking Code (ISO 11469)	>PBT-GF50
Resin ID (ISO 1043)	PBT-GF50

Physical	Nominal Value	Unit	Test Method
Density	1.72	g/cm³	ISO 1183
Molding Shrinkage			ISO 294-4
Transverse flow	1.1	%	ISO 294-4
Flow	0.30	%	ISO 294-4
Water Absorption			ISO 62
Saturated, 23°C, 2.00mm	0.20	%	ISO 62
Balance, 23°C, 2.00mm, 50% RH	0.10	%	ISO 62

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus	16000	MPa	ISO 527-2
Tensile Stress (Break)	160	MPa	ISO 527-2
Tensile Strain (Break)	1.7	%	ISO 527-2
Tensile Creep Modulus			ISO 899-1
1 hr	15000	MPa	ISO 899-1
1000 hr	11600	MPa	ISO 899-1
Flexural Modulus	15000	MPa	ISO 178
Flexural Stress	230	MPa	ISO 178

Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength			ISO 179/1eA
-30°C	12	kJ/m²	ISO 179/1eA
23°C	11	kJ/m²	ISO 179/1eA
Charpy Unnotched Impact Strength			ISO 179/1eU
-30°C	65	kJ/m²	ISO 179/1eU
23°C	55	kJ/m²	ISO 179/1eU
Notched Izod Impact			ISO 180/1A
-30°C	10	kJ/m²	ISO 180/1A
23°C	10	kJ/m²	ISO 180/1A
Unnotched Izod Impact Strength			ISO 180/1U
-30°C	43	kJ/m²	ISO 180/1U
23°C	43	kJ/m²	ISO 180/1U

Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature
0.45 MPa, not annealed	222	°C	ISO 75-2/B
1.8 MPa, not annealed	210	°C	ISO 75-2/A
Vicat Softening Temperature	215	°C	ISO 306/B50
Melting Temperature ¹	224	°C	ISO 11357-3
Linear thermal expansion coefficient			ISO 11359-2
Flow	2.0E-5	cm/cm/°C	ISO 11359-2
Lateral	8.0E-5	cm/cm/°C	ISO 11359-2

Electrical	Nominal Value	Unit	Test Method
Volume Resistivity	> 1.0E+15	ohms·cm	IEC 60093
Dielectric Strength	33	kV/mm	IEC 60243-1
Relative Permittivity			IEC 60250
100 Hz	4.10		IEC 60250
1 MHz	3.90		IEC 60250
Dissipation Factor			IEC 60250
100 Hz	3.8E-3		IEC 60250
1 MHz	0.013		IEC 60250
Comparative Tracking Index	500	V	IEC 60112

Flammability	Nominal Value	Unit	Test Method
Burning Rate ²(1.00 mm)	27	mm/min	ISO 3795
Flame Rating			UL 94, IEC 60695-11-10, -20
0.75 mm	HB		UL 94, IEC 60695-11-10, -20
1.5 mm	HB		UL 94, IEC 60695-11-10, -20
Oxygen Index	20	%	ISO 4589-2
FMVSS Flammability	B		FMVSS 302

Fill Analysis	Nominal Value	Unit
Specific Heat Capacity of Melt	1470	J/kg/°C
Thermal Conductivity of Melt	0.36	W/m/K

Injection	Nominal Value	Unit
Melt Temperature, Optimum	260	°C
Mold Temperature, Optimum	80	°C
Back Pressure	As low as possible
Drying Recommended	yes
Hold Pressure Time	3.00	s/mm

Fill Analysis	Nominal Value	Unit
Melt Density	1.60	g/cm³
Ejection Temperature	170	°C

Injection	Nominal Value	Unit
Drying Temperature	120	°C
Drying Time - Desiccant Dryer	2.0 - 4.0	hr
Suggested Max Moisture	0.040	%
Processing (Melt) Temp	250 - 270	°C
Mold Temperature	30 - 130	°C
Holding Pressure	60.0	MPa

Note Message
1 .	10°C/min
2 .	FMVSS 302

Resin Grade	Manufacturer	Category	Trademark
RTP 300 HF	RTP Company	PC	RTP
Americas Styrenics EC6600	Americas Styrenics LLC	PS (HIPS)	Americas Styrenics
Axiall PVC 8644	Axiall Corporation	PVC, Flexible	Axiall PVC
GPP™ 1001V0M	S&E Specialty Polymers, LLC	TPO (POE)	GPP™
LUVOCOM® 80-8572/BL	LEHVOSS Group	Acetal (POM) Copolymer	LUVOCOM®