Order Products : sales@su-jiao.com
Osterlene® LD-.7-919
| Category: | LDPE , Low Density Polyethylene |
| Manufacturer: | Osterman & Company |
| Trademark: | Osterlene® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | afX5Oq_Osterlene-LD--7-919.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
LD-.7-919 is a series of resins formulated with special antiblock additive and designed for a wide variety of industrial film applications where high impact strength and excellent drawdown are needed. LD-.7-919 meets the requirements of the Food and Drug Administration, 21 CFR Section 177.1520. This regulation allows the use of this olefin polymer in "...articles or components of articles intended for use in contact with food." Specific limitations may apply. |
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 0.919 | g/cm³ | ASTM D1505 |
| Melt Mass-Flow Rate (MFR) (190°C/2.16 kg) | 0.70 | g/10 min | ASTM D1238 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore D) | 46 | ASTM D2240 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength (Yield) | 10.7 | MPa | ASTM D638 |
| Tensile Elongation (Yield) | 100 | % | ASTM D638 |
| Films | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Secant Modulus - 1% Secant, MD | 179 | MPa | ASTM D882 |
| Tensile Strength - MD (Yield) | 23.4 | MPa | ASTM D882 |
| Tensile Elongation - MD (Yield) | 160 | % | ASTM D882 |
| Dart Drop Impact 1 | 130 | g | ASTM D1709 |
| Elmendorf Tear Strength - MD | 300 | g | ASTM D1922 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Brittleness Temperature | -75.0 | °C | ASTM D746 |
| Vicat Softening Temperature | 90.0 | °C | ASTM D1525 |
| Additional Information |
|---|
| The value shown as Secant Modulus, ASTM D882, was tested in accordance with ASTM E111.Product LD-.7-919-AM: Slip - None, Antiblock - MediumProduct LD-.7-919-SH: Slip - High, Antiblock - None |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Melt Temperature | 154 - 177 | °C |
| Extrusion instructions |
|---|
| Generally recommended extrusion conditions include a melt temperature range of 310 - 350°F and a blow-up ratio rate of 1.8-2.5:1.Drawdown to gauges below 1.0 mils (<25 microns) is possible at commercial rates when proper techniques are used. Specific recommendations for processing can only be made when the processing conditions, equipment and end use are known. |
| Note Message | |
|---|---|
| 1 . | F50 |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| SILVER® SA-5302 | Guangdong Silver Age Sci & Tech. Co., Ltd | Polyolefin, Unspecified | SILVER® |
| Axplas® r-PP63 0000 | Axion Polymers | PP, Unspecified | Axplas® |
| CERTENE™ HHP-0449 | Muehlstein | HDPE | CERTENE™ |
| LNP™ LUBRICOMP™ KZL16 compound | SABIC Innovative Plastics | Acetal (POM) Copolymer | LNP™ LUBRICOMP™ |
| Durethan® BKV 215 H2.0 901510 | LANXESS GmbH | Nylon 6 | Durethan® |
