Order Products : sales@su-jiao.com
Kingfa ABP-2020
| Category: | PP, Unspecified , Polypropylene |
| Manufacturer: | Kingfa |
| Trademark: | Kingfa |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | Yx6T9v_Kingfa-ABP-2020.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| PP-EPDM-T20 |
| General Information | |
|---|---|
| Filler / Reinforcement |
|
| Additive |
|
| Features |
|
| Uses |
|
| Appearance |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.02 - 1.06 | g/cm³ | ISO 1183 |
| Melt Mass-Flow Rate (MFR) (230°C/2.16 kg) | 18 - 25 | g/10 min | ISO 1133 |
| Molding Shrinkage | Internal method | ||
| 23°C | 8.5E-3 - 9.5E-3 | % | Internal method |
| 80°C, 30 minutes | 1.0E-3 - 1.5E-3 | % | Internal method |
| 120°C, 30 minutes | 1.5E-3 - 2.0E-3 | % | Internal method |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress (Break) | 18.0 | MPa | ISO 527-2/50 |
| Tensile Strain (Break) | 50 | % | ISO 527-2/50 |
| Flexural Modulus 1 | 1500 | MPa | ISO 178 |
| Flexural Stress 2 | 25.0 | MPa | ISO 178 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Notched Izod Impact 3(23°C) | 35 | kJ/m² | ISO 180 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Heat Deflection Temperature (0.45 MPa, unannealed, 4.00mm span) | 104 | °C | ISO 75-2/B |
| Flammability | Nominal Value | Test Method | |
|---|---|---|---|
| Flame Rating 4 | HB | ISO 3795 |
| Additional Information | Nominal Value | Test Method | |
|---|---|---|---|
| Weather Resistance 5 | 4.00 - 5.00 | SAE J1960 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 80.0 | °C | |
| Drying Time | 0.0 - 2.0 | hr | |
| Rear Temperature | 190 - 210 | °C | |
| Middle Temperature | 205 - 230 | °C | |
| Front Temperature | 215 - 240 | °C | |
| Processing (Melt) Temp | 220 - 245 | °C | |
| Mold Temperature | 30.0 - 60.0 | °C | |
| Injection Rate | Slow-Moderate | ||
| Back Pressure | 0.350 | MPa |
| Injection instructions |
|---|
| Processing Temp. Limit: 250°C |
| Note Message | |
|---|---|
| 1 . | 2.0 mm/min |
| 2 . | 2.0 mm/min |
| 3 . | 4 mm |
| 4 . | 360×100×3 |
| 5 . | 250 kJ/m² |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Maxxam™ GV-819.G001-8065 | PolyOne Corporation | PP, Unspecified | Maxxam™ |
| Nycast 612VS C-90 | Cast Nylons Ltd. | Nylon 612 | Nycast |
| CarmelStat™ CS 1118 | Carmel Olefins Ltd. | PP, Unspecified | CarmelStat™ |
| Delta N66R-1M80 | Delta Polymers | Nylon 66 | Delta |
| Plaslube® PEEK CF10 GL10 TL10 A HF | Techmer Engineered Solutions | PEEK | Plaslube® |
