Dynalloy™ OBC 8100-N50 Datasheet,TPE,PolyOne Corporation-SHANGHAI SUSHENG

Message
DYNALLOY™OBC8100-N50 is a kind of using Dow INFUSE™TPE material with unique characteristics of olefin block polymer. 8100 series of materials are specially developed for TPE applications that require direct contact with food. New Products. Commercial norms have not yet been established. can be bonded to polypropylene direct contact with food strong liquidity Excellent coloring

General Information
Features	Good liquidity Good coloring Compliance of Food Exposure
Uses	overmolding Kitchen utensils Non-specific food applications Household goods Soft touch application Food service sector
Agency Ratings	BfR food contact, not rated 2 FDA 21 CFR 177.2600 3 European 2002/72/EC 4
RoHS Compliance	RoHS compliance
Appearance	Natural color
Forms	Particle
Processing Method	Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.06	g/cm³	ASTM D792

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore A, 10 sec)	48		ASTM D2240

Elastomers	Nominal Value	Unit	Test Method
Tensile Stress ¹			ASTM D412
100% strain, 23°C ²	1.48	MPa	ASTM D412
300% strain, 23°C ³	1.90	MPa	ASTM D412
Tensile Strength (Break, 23°C)	3.31	MPa	ASTM D412
Tensile Elongation (Break, 23°C)	990	%	ASTM D412
Tear Strength	17.5	kN/m	ASTM D624

Fill Analysis	Nominal Value	Unit	Test Method
Apparent Viscosity			ASTM D3835
200°C, 1340 sec^-1	112	Pa·s	ASTM D3835
200°C, 11200 sec^-1	22.9	Pa·s	ASTM D3835

Injection	Nominal Value	Unit
Rear Temperature	160 - 188	°C
Middle Temperature	177 - 193	°C
Front Temperature	182 - 210	°C
Nozzle Temperature	193 - 216	°C
Mold Temperature	15.6 - 26.7	°C
Back Pressure	0.00 - 0.689	MPa
Screw Speed	25 - 100	rpm

Injection instructions
以聚丙烯 (PP)、乙烯醋酸乙烯共聚物 (EVA) 或低密度聚乙烯 (PE) 为基础的色母料最适合 DYNALLOY™ OBC 8100-N50 着色。使用熔体流动速率较高（范围为 25 - 40 克/10 分钟）的色母料，则能达到较好的颜色分散效果。典型的色母料用量为 1% 至 5%（重量）。不应采用以 PVC 为基础的色母料。色母料是否适用，应由用户通过试验来最终确定。在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。DYNALLOY™ OBC 8100-N50 具有极好的熔体稳定性。最长停留时间可能会根据机筒尺寸有所变化。通常，如果机器闲置 8 - 10 分钟或以上，则应将机筒排空。不需要干燥注射速度：1 - 3 英寸/秒第一阶段 - 提升压力：175 - 800 psi第二阶段 - 保持压力：30% 的升压保持时间（厚部件）：3 - 10 秒保持时间（薄部件）：1 - 3 秒

Injection instructions

以聚丙烯 (PP)、乙烯醋酸乙烯共聚物 (EVA) 或低密度聚乙烯 (PE) 为基础的色母料最适合 DYNALLOY™ OBC 8100-N50 着色。使用熔体流动速率较高（范围为 25 - 40 克/10 分钟）的色母料，则能达到较好的颜色分散效果。典型的色母料用量为 1% 至 5%（重量）。不应采用以 PVC 为基础的色母料。色母料是否适用，应由用户通过试验来最终确定。在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。DYNALLOY™ OBC 8100-N50 具有极好的熔体稳定性。最长停留时间可能会根据机筒尺寸有所变化。通常，如果机器闲置 8 - 10 分钟或以上，则应将机筒排空。不需要干燥注射速度：1 - 3 英寸/秒第一阶段 - 提升压力：175 - 800 psi第二阶段 - 保持压力：30% 的升压保持时间（厚部件）：3 - 10 秒保持时间（薄部件）：1 - 3 秒

Note Message
1 .	2 hours
2 .	Mouth die c
3 .	C mould

Category:	TPE , Thermoplastic Elastomer
Manufacturer:	PolyOne Corporation
Trademark:	Dynalloy™
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	W0NHGg_Dynalloy-OBC-8100-N50.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
RheTech Polypropylene HP514-197	RheTech, Inc.	PP Copolymer	RheTech Polypropylene
RTP 1200 S-40D	RTP Company	TPU-Polyester	RTP
Colorite G Series 7811G-015	Colorite Polymers	PVC, Flexible	Colorite G Series
FHR Polypropylene P5M2Z-012	Flint Hills Resources, LP	PP Random Copolymer	FHR Polypropylene
Keysor PVC KYNS	Keysor-Century Corporation	PVC, Unspecified	Keysor PVC