AXELERON™ CX 0078 NT CPD

Category:	LDPE , Nucleating Agent Masterbatch
Manufacturer:	The Dow Chemical Company
Trademark:	AXELERON™
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	QDhfws_AXELERON-CX-0078-NT-CPD.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

Message
AXELERON™CX A- 0078 NT is a nucleating agent used for gas injection cell insulation used in high-performance coaxial cables. Typical end applications include 75 ohm CATV distribution cables and trunk coaxial cables, or thicker 50 ohm RF coaxial cables for mobile phone technology. AXELERON™CX A- 0078 NT uses HP LDPE as the base resin, to which a 10% nucleating agent with low loss is added. Before gas injection, the masterbatch must be combined with HDPE, LDPE material and AXELERON™CX 6944 NT CPD HDPE, AXELERON™CX 1253 NT CPD LDPE were dry mixed separately. In order to optimize the foaming and cell structure, the nucleating agent content should be 0.1-0.3%, that is to say, the masterbatch content in the blend should be 1-3%. Due to the excellent electrical properties of this material, it is particularly suitable for manufacturing thick-walled (>7mm insulating material) foamed insulating materials. It can also endow the product with excellent processing performance, easy foaming, and foaming rate up to 80%.

General Information
Additive	Nucleating agent
Uses	Coaxial Cable Insulation Wire and cable applications Masterbatch Foam
Forms	Particle
Processing Method	Extrusion

Physical	Nominal Value	Unit	Test Method
Specific Gravity	0.970	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR) ¹(190°C/2.16 kg)	2.0	g/10 min	ASTM D1238

Extrusion instructions
AXELERON™ CX 0078 NT CPD is designed to be extruded with Dow's gas injection compounds AXELERON™ CX 6944 NT CPD HDPE and AXELERON™ CX 1253 NT CPD LDPE. It is normally added at 1-3 % masterbatch concentration into a blend of 60-80% 6944 and 20-40% 1253.While the exact temperature profile required will depend upon the screw design and construction being made, the following extrusion temperature profile represents a good starting point: Feed Zone: 285-300°F (140-150°C) Transition Zone: 340-355°F (170-180°C) Gas Injection Point: 355-410°F (190-210°C) Metering Zone: 285-340°F (140-170°C); depends on diameter insulation Crosshead and Die: 265-320°F (130-160°C); depends on diameter insulation

Extrusion instructions

AXELERON™ CX 0078 NT CPD is designed to be extruded with Dow's gas injection compounds AXELERON™ CX 6944 NT CPD HDPE and AXELERON™ CX 1253 NT CPD LDPE. It is normally added at 1-3 % masterbatch concentration into a blend of 60-80% 6944 and 20-40% 1253.While the exact temperature profile required will depend upon the screw design and construction being made, the following extrusion temperature profile represents a good starting point: Feed Zone: 285-300°F (140-150°C) Transition Zone: 340-355°F (170-180°C) Gas Injection Point: 355-410°F (190-210°C) Metering Zone: 285-340°F (140-170°C); depends on diameter insulation Crosshead and Die: 265-320°F (130-160°C); depends on diameter insulation

Note Message
1 .	Base Resin

Resin Grade	Manufacturer	Category	Trademark
Westlake LDPE EC4056AA	Westlake Chemical Corporation	LDPE	Westlake LDPE
AIE PA66 60G3	Asia International Enterprise (Hong Kong) Limited	Nylon 66	AIE PA66
Hifax TRC 103P R299	LyondellBasell Industries	PP Impact Copolymer	Hifax
LNP鈩?VERTON鈩?RV0079 compound	SABIC Innovative Plastics	Nylon 66	LNP™ VERTON™
Edistir® N 3380	Versalis S.p.A.	PS (GPPS)	Edistir®