Order Products : sales@su-jiao.com
Lustran® ABS 1146
| Category: | ABS , Acrylonitrile Butadiene Styrene |
| Manufacturer: | INEOS ABS (USA) |
| Trademark: | Lustran® ABS |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | PDkgGp_Lustran-ABS-1146.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Lustran ABS 1146 resin is a very high-impact grade of ABS (acrylonitrile butadiene styrene). This automotive injection molding grade offers a good balance of physical properties with high ductility at low temperatures. Lustran ABS 1146 resin is used for automotive applications where impact strength and a non-brittle type of failure mode are needed. Typical applications include interior trim parts, lower steering column shrouds, glove box doors, tail lamp housings, and instrument panel carriers. As with any product, use of Lustran ABS 1146 resin in a given application must be tested (including field testing, etc.) in advance by the user to determine suitability. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.03 | g/cm³ | ASTM D792 |
| Specific Volume | 0.970 | cm³/g | ASTM D792 |
| Melt Mass-Flow Rate (MFR) | ASTM D1238 | ||
| 200°C/10.0 kg | 4.0 | g/10 min | ASTM D1238 |
| 230°C/3.8 kg | 1.0 | g/10 min | ASTM D1238 |
| Molding Shrinkage - Flow | 0.60 - 0.80 | % | ASTM D955 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness (R-Scale) | 100 | ASTM D785 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus | 2340 | MPa | ASTM D638 |
| Tensile Strength | |||
| Yield | 39.3 | MPa | ASTM D638 |
| Yield | 42.0 | MPa | ISO 527-2 |
| Flexural Modulus | |||
| -- | 2410 | MPa | ASTM D790 |
| -- | 2390 | MPa | ISO 178 |
| Flexural Strength (Yield) | 64.8 | MPa | ASTM D790 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Notched Izod Impact | |||
| 23°C, 3.18 mm | 510 | J/m | ASTM D256 |
| 23°C 1 | 38 | kJ/m² | ISO 180 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load | ASTM D648 | ||
| 0.45 MPa, unannealed, 3.18mm | 92.2 | °C | ASTM D648 |
| 0.45 MPa, annealed, 12.7mm | 100 | °C | ASTM D648 |
| 1.8 MPa, unannealed, 3.18mm | 78.3 | °C | ASTM D648 |
| 1.8 MPa, annealed, 12.7mm, molded | 105 | °C | ASTM D648 |
| 1.8 MPa, annealed, 12.7mm | 95.0 | °C | ASTM D648 |
| Vicat Softening Temperature | |||
| -- | 106 | °C | ASTM D1525 2 |
| -- | 96.0 | °C | ISO 306/B50 |
| CLTE - Flow (-30 to 30°C) | 9.2E-5 | cm/cm/°C | ASTM D696 |
| RTI Elec (1.57 mm) | 60.0 | °C | UL 746 |
| RTI Imp (1.57 mm) | 60.0 | °C | UL 746 |
| RTI (1.57 mm) | 60.0 | °C | UL 746 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Burning Rate 3 | 25 | mm/min | SAE J1685 |
| Flame Rating | UL 94 | ||
| 1.57 mm | HB | UL 94 | |
| 3.18 mm | HB | UL 94 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | |||
| A | 82.2 - 87.8 | °C | |
| B | 71.1 - 76.7 | °C | |
| Drying Time | |||
| A | 2.0 | hr | |
| B | 4.0 | hr | |
| Suggested Max Moisture | < 0.10 | % | |
| Suggested Shot Size | 50 - 75 | % | |
| Suggested Max Regrind | 20 | % | |
| Rear Temperature | 238 - 254 | °C | |
| Middle Temperature | 243 - 260 | °C | |
| Front Temperature | 249 - 266 | °C | |
| Nozzle Temperature | 249 - 271 | °C | |
| Processing (Melt) Temp | 249 - 271 | °C | |
| Mold Temperature | 48.9 - 71.1 | °C | |
| Injection Rate | Fast | ||
| Back Pressure | 0.172 - 0.689 | MPa | |
| Clamp Tonnage | 2.8 - 5.5 | kN/cm² | |
| Cushion | < 6.35 | mm | |
| Screw L/D Ratio | 20.0:1.0 | ||
| Screw Compression Ratio | 2.5:1.0 |
| Injection instructions |
|---|
| Hold Pressure: 50 to 75% of Injection PressureScrew Speed: Moderate |
| Note Message | |
|---|---|
| 1 . | 1x10 mm bar |
| 2 . | 标准 B (120°C/h), 压 力1 (10N) |
| 3 . | 2x100x355 mm |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Fasal® BIO 337 | Fasal Wood KG | Biodeg Polymers | Fasal® |
| Ferro PP LPP40BC22BK | Ferro Corporation | PP Homopolymer | Ferro PP |
| EMERGE™ PC 8600-20 | Trinseo | PC | EMERGE™ |
| Petrothene® NA285003 | LyondellBasell Industries | MDPE | Petrothene® |
| Sylvin 4260-60 Natural | Sylvin Technologies Incorporated | PVC, Unspecified | Sylvin |
