Order Products : sales@su-jiao.com
UNIGARD™ HP DGDD-1430 NT
| Category: | TP, Unspecified , Halogenated Flame Retardant Insulation Compound |
| Manufacturer: | The Dow Chemical Company |
| Trademark: | UNIGARD™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | NFrgZ5_UNIGARD-HP-DGDD-1430-NT.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Thermoplastic flame retardant materials UNIGARD™HP DGDD-1430 Natural is a flame retardant, thermoplastic and insulating material used in communication cables. It has a good balance between high flame retardant properties, excellent electrical and physical properties, and good processing properties. DGDD-1430 Natural have a wide range of applications, including thin-walled insulation materials and COAX insulation materials used to meet NEC Article 725 and 800 requirements. When appropriate cable design and sheath material are selected, the material can make the cable meet the requirements of IEEE-383/UL-1581 vertical bracket cable, Canadian Standards Association (CSA) FT-4 vertical bracket cable and UL-1666 rising cable combustion test. |
| General Information | |
|---|---|
| Uses |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.48 | g/cm³ | ASTM D1505 |
| Melt Mass-Flow Rate (MFR) | 0.75 | g/10 min | ASTM D1238 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength 1 | 14.5 | MPa | ASTM D638 |
| Tensile Elongation 2(Break) | 500 | % | ASTM D638 |
| Aging | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile strength retention- 7 days 3(121°C) | 90 | % | ASTM D638 |
| Elongation retention rate- 7 days 4(121°C) | 90 | % | ASTM D638 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Dielectric Constant | ASTM D1531 | ||
| 100 kHz | 2.59 | ASTM D1531 | |
| 1 MHz | 2.59 | ASTM D1531 | |
| Dissipation Factor | ASTM D1531 | ||
| 100 kHz | 2.0E-4 | ASTM D1531 | |
| 1 MHz | 2.0E-4 | ASTM D1531 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Flame Rating (0.500 mm) | V-0 | UL 94 | |
| Oxygen Index | 29 | % | ASTM D2863 |
| Extrusion instructions |
|---|
| Typical extrusion conditions are listed below. Exact conditions will depend upon the equipment used and the application.Extruder Screw L/D: 15:1 to 24:1 Screw Suggested: Polyethylene metering Compression Ratio: 2.5:1 to 3.5:1 Screen Pack: 20/40/60/20 mesh Extrusion Temperatures Barrel Feed Zone: 360°F (182°C) Barrel Transition Zone: 420°F (215°C) Barrel Metering Zone: 440°F (227°C) Crosshead Zone: 440°F (227°C) Melt Temperature: 440°F (227°C) Wire Preheat Temperature: 280°F (138°C) Die PE type double taper Die Size Finish Diameter +0.001 in Coloring UNIGARD HP DGDD-1430 Natural insulations should be colored with polyethylene homopolymer based color masterbatches. Avoid EVA copolymer-based masterbatches, which would be detrimental to insulation electrical performance. The high flame-retardant composition of DGDD-1430 Natural will reduce color intensity, and increased color masterbatch loadings may be required. |
| Note Message | |
|---|---|
| 1 . | Based on 22 AWG (0.643 mm dia.) copper with 0.014 in. insulation. |
| 2 . | Based on 22 AWG (0.643 mm dia.) copper with 0.014 in. insulation. |
| 3 . | Based on 22 AWG (0.643 mm dia.) copper with 0.014 in. insulation. |
| 4 . | Based on 22 AWG (0.643 mm dia.) copper with 0.014 in. insulation. |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Staramide RFC16 | Eurostar Engineering Plastics | Nylon 66/6 | Staramide |
| APEX® 3701-70NT1 | Teknor Apex Company | PVC, Flexible | APEX® |
| Di-Pak™ E-4651-3 | Hapco Inc. | TP, Unspecified | Di-Pak™ |
| LG ABS MP211 | LG Chem Ltd. | ABS | LG ABS |
| LNP™ THERMOCOMP™ UF006H compound | SABIC Innovative Plastics | PPA | LNP™ THERMOCOMP™ |
