Order Products : sales@su-jiao.com
Sasol Polymers PE LT388
| Category: | LDPE , Low Density Polyethylene |
| Manufacturer: | Sasol Polymers |
| Trademark: | Sasol Polymers PE |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | MSV2DK_Sasol-Polymers-PE-LT388.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
Features
Applications
|
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 0.922 | g/cm³ | ASTM D1505 |
| Melt Mass-Flow Rate (MFR) (190°C/2.16 kg) | 2.0 | g/10 min | ASTM D1238 |
| Films | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Film Thickness - Tested | 30 | µm | |
| Tensile Strength | ASTM D882 | ||
| MD : Yield, 30 µm, blown film | 9.00 | MPa | ASTM D882 |
| TD : Yield, 30 µm, blown film | 9.00 | MPa | ASTM D882 |
| MD : Broken, 30 µm, blown film | 23.0 | MPa | ASTM D882 |
| TD : Broken, 30 µm, blown film | 19.0 | MPa | ASTM D882 |
| Tensile Elongation | ASTM D882 | ||
| MD : Yield, 30 µm, blown film | 370 | % | ASTM D882 |
| TD : Yield, 30 µm, blown film | 560 | % | ASTM D882 |
| Dart Drop Impact 1(30 µm, Blown Film) | 70 | g | ASTM D1709 |
| Elmendorf Tear Strength | ASTM D1922 | ||
| MD : 30 µm, blown film | 6.0 | g | ASTM D1922 |
| TD : 30 µm, blown film | 5.0 | g | ASTM D1922 |
| Optical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Gloss | 70 | ASTM D2457 | |
| Clarity | 65.0 | ASTM D1746 | |
| Haze | 6.0 | % | ASTM D1003 |
| Additional Information |
|---|
| The above values were measured on 30µm film produced on a 65mm Macchi extruder with a Macchi LDPE screw and a 250mm die, using 207°C melt temperature, 625mm FLH, 2.5:1 blow ratio and a die gap of 0.8mm. |
| Extrusion | Nominal Value | Unit | |
|---|---|---|---|
| Hopper Temperature | 125 - 140 | °C | |
| Cylinder Zone 1 Temp. | 130 - 145 | °C | |
| Cylinder Zone 2 Temp. | 140 - 155 | °C | |
| Cylinder Zone 3 Temp. | 150 - 165 | °C | |
| Cylinder Zone 4 Temp. | 155 - 170 | °C | |
| Melt Temperature | 190 - 210 | °C | |
| Die Temperature | 160 - 170 | °C |
| Extrusion instructions |
|---|
| Should be processed on a conventional LDPE extruder, but can be processed on a LLDPE extruder (wide die gap) with drawdown limitations, inferior mechanical and film shrinkage properties. Recommended screen pack: 60/100/60 BS mesh. |
| Note Message | |
|---|---|
| 1 . | F50 |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Rotec® ABS 1001 GF 10 | ROMIRA GmbH | ABS | Rotec® ABS |
| NYCOA Polyamide 715 C | Nycoa (Nylon Corporation of America) | Nylon 6 | NYCOA Polyamide |
| Karina BROWN PVC COMPOUND 800-36/217-A-ERYB | Karina Ind. e Com. de Plásticos Ltda | PVC, Unspecified | Karina |
| MAJ'ECO DP290MBSE | AD majoris | PE, Unspecified | MAJ'ECO |
| Paracril® BJLT HX | INSA | NBR | Paracril® |
