TECHNYL eXten® D 218CR V33 BLACK Datasheet,Nylon 66/610,Solvay Engineering Plastics-SHANGHAI SUSHENG

Message
TECHNYL eXten® D 218CR V33 Black is a glass fiber reinforced grade based on polyamide blend of polyamide 6.10 and polyamide 66, heat stabilized, for injection moulding. This grade shows outstanding resistance to hydrolysis and chemical resistance to long life automotive coolants. It also offers an excellent crack resistance to calcium chloride road salts, good injection process ability, high surface aspect quality, and high overall mechanical and thermal properties.

General Information
Filler / Reinforcement	Glass fiber reinforced material, 33% filler by weight
Additive	Hydrolysis resistance
Features	Heat Stabilized - Inorganic Road Salt Resistant Ultra High Glycol Resistance Good dimensional stability Low hygroscopicity Weldable Good liquidity Good chemical resistance Hydrolysis resistance Excellent appearance
Uses	Application in Automobile Field
Agency Ratings	EC 1907/2006 (REACH)
RoHS Compliance	RoHS compliance
Appearance	Black
Forms	Particle
Processing Method	Injection molding
Multi-Point Data	Isothermal Stress vs. Strain (ISO 11403-1) Viscosity vs. Shear Rate (ISO 11403-2)
Resin ID (ISO 1043)	PA610+PA66-GF33

Physical	Dry	Conditioned	Unit	Test Method
Density	1.35	--	g/cm³	ISO 1183/A
Water Absorption				ISO 62
23°C, 24 hr	0.30	--	%	ISO 62
Saturated, 23°C	3.6	--	%	ISO 62
Equilibrium, 23°C, 50% RH	1.3	--	%	ISO 62

Mechanical	Dry	Conditioned	Unit	Test Method
Tensile Modulus (23°C)	11300	8900	MPa	ISO 527-2/1A
Tensile Stress (Break, 23°C)	196	132	MPa	ISO 527-2/1A
Tensile Strain (Break, 23°C)	3.3	4.8	%	ISO 527-2
Flexural Modulus (23°C)	10200	8000	MPa	ISO 178
Flexural Stress (23°C)	280	220	MPa	ISO 178

Impact	Dry	Conditioned	Unit	Test Method
Charpy Notched Impact Strength (23°C)	15	--	kJ/m²	ISO 179/1eA
Charpy Unnotched Impact Strength				ISO 179/1eU
-30°C	70	--	kJ/m²	ISO 179/1eU
23°C	94	--	kJ/m²	ISO 179/1eU

Thermal	Dry	Conditioned	Unit	Test Method
Heat Deflection Temperature
0.45 MPa, not annealed	225	--	°C	ISO 75-2/Bf
1.8 MPa, not annealed	218	--	°C	ISO 75-2/Af
Melting Temperature	220 - 260	--	°C	ISO 11357-3

Electrical	Dry	Conditioned	Unit	Test Method
Volume Resistivity	1.0E+15	--	ohms·cm	IEC 60093
Dielectric Strength (2.00 mm)	34	--	kV/mm	IEC 60243-1
Comparative Tracking Index (Solution B)	600	--	V	IEC 60112

Flammability	Dry	Conditioned	Unit	Test Method
Flame Rating (0.40 mm)	HB	--		UL 94

Injection	Dry	Unit
Drying Temperature	80	°C
Suggested Max Moisture	0.20	%
Rear Temperature	265 - 275	°C
Middle Temperature	270 - 280	°C
Front Temperature	275 - 285	°C
Mold Temperature	70 - 100	°C

Injection instructions
The material is supplied in airtight bags, ready for use. In case that the virgin material has absorbed moisture, it must be dried with a dehumidified air drying equipment, dew point mini -20°C. Recommended time 2-4hInjection Advice: For reinforced polyamide, Solvay recommends the use of steel with a high content of Carbon and purified for polishing to avoid or limit the abrasion. For example: X38CrMoV5-1 (EN Norm) - 1.2367 /1.2343 (DIN Norm) or X160CrMoV12 (EN Norm) - 1.2601 /1.2379 (DIN Norm). For Mould Temperature, in the case of parts where the surface roughness is required we can recommend a temperature of 90°C to 120°C with an optimum at 105°C. The processing parameters like processing temperatures are a recommendation and can be adjusted in function of injection machine size, part geometry / design

Injection instructions

The material is supplied in airtight bags, ready for use. In case that the virgin material has absorbed moisture, it must be dried with a dehumidified air drying equipment, dew point mini -20°C. Recommended time 2-4hInjection Advice: For reinforced polyamide, Solvay recommends the use of steel with a high content of Carbon and purified for polishing to avoid or limit the abrasion. For example: X38CrMoV5-1 (EN Norm) - 1.2367 /1.2343 (DIN Norm) or X160CrMoV12 (EN Norm) - 1.2601 /1.2379 (DIN Norm). For Mould Temperature, in the case of parts where the surface roughness is required we can recommend a temperature of 90°C to 120°C with an optimum at 105°C. The processing parameters like processing temperatures are a recommendation and can be adjusted in function of injection machine size, part geometry / design

Category:	Nylon 66/610 , Polyamide 66/610 Copolymer
Manufacturer:	Solvay Engineering Plastics
Trademark:	TECHNYL eXten®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	LsDTxL_TECHNYLeXtenD218CRV33BLACK.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
Generic Nylon 12 - Glass Fiber	Generic	Nylon 12	Generic
Dynaflex™ G7990-9001-02	PolyOne Corporation	TPE	Dynaflex™
Rotuba CAP CP800 (17% Plasticizer)	Rotuba Extruders, Inc.	CAP	Rotuba CAP
ZEONOR® 1420R	Zeon Corporation	COP	ZEONOR®
LEXAN™ SLX1432 resin	SABIC Innovative Plastics	PC	LEXAN™