LUVOCOM® 1880-8748 Datasheet,LCP,Lehmann & Voss & Co.-SHANGHAI SUSHENG

Message
LUVOCOM®1880-8748 is a liquid crystal polymer (LCP) material,. This product is available in North America, Africa and the Middle East, Latin America, Europe or Asia Pacific,. LUVOCOM®The main features of 1880-8748 are: Good dimensional stability Good stiffness Wear-resistant Lubrication Typical application areas include: Electrical/electronic applications engineering/industrial accessories Aerospace medical/health care

General Information
Additive	PTFE lubricant
Features	Good dimensional stability Rigid, good Good strength Good wear resistance Lubrication
Uses	Electrical/Electronic Applications Engineering accessories Aerospace applications Medical/nursing supplies
Appearance	Grey

Physical	Nominal Value	Unit	Test Method
Density	1.46	g/cm³	ISO 1183
Molding Shrinkage	0.0 - 0.10	%	DIN 16901
Water Absorption (23°C, 24 hr)	< 0.010	%

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus	9000	MPa	ISO 527-2
Tensile Stress (Break)	145	MPa	ISO 527-2
Tensile Strain (Yield)	3.2	%	ISO 527-2
Flexural Modulus	8000	MPa	ISO 178
Flexural Stress	190	MPa	ISO 178
Coefficient of Friction
Dynamic	0.16
Static	0.22
Flexural Strain at Flexural Strength	4.0	%	ISO 178

Thermal	Nominal Value	Unit	Test Method
Maximum operating temperature- Short Term	230	°C

Electrical	Nominal Value	Unit	Test Method
Insulation Resistance	> 1.0E+12	ohms	IEC 60167

Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength (23°C)	33	kJ/m²	ISO 179/1eA
Charpy Unnotched Impact Strength (23°C)	90	kJ/m²	ISO 179/1eU

Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature (1.8 MPa, Unannealed)	225	°C	ISO 75-2/A
Continuous Use Temperature	190	°C	UL 746B

Electrical	Nominal Value	Unit	Test Method
Surface Resistivity	> 1.0E+12	ohms	IEC 60093

Injection	Nominal Value	Unit
Drying Temperature
A	130 - 150	°C
Vacuum dryer, B	150	°C
Drying Time
A	3.0 - 5.0	hr
Vacuum dryer, B	4.0 - 5.0	hr
Suggested Max Moisture	0.020	%
Rear Temperature	290 - 330	°C
Middle Temperature	310 - 340	°C
Front Temperature	320 - 340	°C
Nozzle Temperature	300 - 320	°C
Processing (Melt) Temp	320	°C
Mold Temperature	90.0 - 130	°C

Injection instructions
General In general LUVOCOM® can be processed on conventional injection moulding machines while observing the usual technical guidelines. Any added fibrous materials or fillers may have an abrasive effect. In this case the cylinder and screw should be protected against wear as is usual in the processing of reinforced thermoplastic materials. Lengthy dwell times for the melts in the cylinder should be avoided. Lower the temperatures during interruptions! Predrying (optional) It is advisable to predry the granulate with a suitable dryer immediately before processing. The granulate may absorb moisture from the air. Delivery Form & Storage Unless indicated otherwise, the material is delivered as 3mm-long pellets in sealed bags on pallets. Preferably storage should be effected in dry and normally temperatured rooms Additional Information During processing the moisture level should not exceed 0.02%, otherwise molecular degradation and surface defects (e.g. smearing) may occur. As the material absorbs water very quickly, the predried material should be fed to the processing immediately. Processing temperatures above 300°C may very rapidly cause thermal damage and should therefore be avoided. The processing notes provided merely represent a recommendation for general use. Due to the large variety of machines, geometries and volumes of parts, etc., it may be necessary to employ different settings according to the specific application. Please contact us for further information.

Injection instructions

General In general LUVOCOM® can be processed on conventional injection moulding machines while observing the usual technical guidelines. Any added fibrous materials or fillers may have an abrasive effect. In this case the cylinder and screw should be protected against wear as is usual in the processing of reinforced thermoplastic materials. Lengthy dwell times for the melts in the cylinder should be avoided. Lower the temperatures during interruptions! Predrying (optional) It is advisable to predry the granulate with a suitable dryer immediately before processing. The granulate may absorb moisture from the air. Delivery Form & Storage Unless indicated otherwise, the material is delivered as 3mm-long pellets in sealed bags on pallets. Preferably storage should be effected in dry and normally temperatured rooms Additional Information During processing the moisture level should not exceed 0.02%, otherwise molecular degradation and surface defects (e.g. smearing) may occur. As the material absorbs water very quickly, the predried material should be fed to the processing immediately. Processing temperatures above 300°C may very rapidly cause thermal damage and should therefore be avoided. The processing notes provided merely represent a recommendation for general use. Due to the large variety of machines, geometries and volumes of parts, etc., it may be necessary to employ different settings according to the specific application. Please contact us for further information.

Category:	LCP , Liquid Crystal Polymer
Manufacturer:	Lehmann & Voss & Co.
Trademark:	LUVOCOM®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	LiW6xV_LUVOCOM-1880-8748.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
RTP EMI 332 G FR	RTP Company	PC	RTP
ACCUCOMP™ ASA002L	ACLO Compounders Inc.	ASA	ACCUCOMP™
Di-Pak™ E-4056	Hapco Inc.	TP, Unspecified	Di-Pak™
Latishield 66-10A H2 CETG/400	LATI S.p.A.	Nylon 66	Latishield
Karina IVORY PVC COMPOUND 951-35/ 4-IS-LMP	Karina Ind. e Com. de Plásticos Ltda	PVC, Unspecified	Karina