Order Products : sales@su-jiao.com

Sasol Polymers PE HR486

Category:	LLDPE , Linear Low Density Polyethylene
Manufacturer:	Sasol Polymers
Trademark:	Sasol Polymers PE
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	L5Ib0V_Sasol-Polymers-PE-HR486.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

WECHAT

Message

Features

High rigidity

Excellent impact strength

Excellent chemical resistance

Good ESCR

Heat and UV resistant

Tough and abrasion resistant

Colourable

Hexene copolymer

Applications

Large agricultural tanks

Large industrial tanks

Solar panels

Outdoor use

General Information
Additive	Antioxidation demoulding UV stabilizer
Features	Rigidity, high High ESCR (Stress Cracking Resistance) Copolymer hexene comonomer Antioxidation Impact resistance, high Good UV resistance Good coloring Good wear resistance Good chemical resistance Heat resistance, medium Good toughness Compliance of Food Exposure
Uses	Industrial application Agricultural water tank Outdoor application Water tank Solar panel
Agency Ratings	EC 1935/2004 FDA 21 CFR 177.1520(a)(3)(i)(c)(1) FDA 21 CFR 177.1520(c) 3.1a
Forms	Particle
Processing Method	rotomolding

Physical	Nominal Value	Unit	Test Method
Density	0.939	g/cm³	ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)	3.5	g/10 min	ASTM D1238
Environmental Stress-Cracking Resistance (100% Igepal CO-630, F50)	> 500	hr	ASTM D1693

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore D)	61		ASTM D2240

Mechanical	Nominal Value	Unit	Test Method
Tensile Strength ¹			ASTM D638
Yield	19.0	MPa	ASTM D638
Fracture	24.0	MPa	ASTM D638
Tensile Elongation ²(Break)	830	%	ASTM D638
Flexural Modulus	837	MPa	ASTM D790

Thermal	Nominal Value	Unit	Test Method
Vicat Softening Temperature	120	°C	ASTM D1525
Impact test ³(-40°C, 5.00 mm)	350	J/cm	ASTM D3029

Injection	Nominal Value	Unit
Rear Temperature	140 - 170	°C
Middle Temperature	150 - 180	°C
Front Temperature	160 - 190	°C
Nozzle Temperature	180 - 200	°C
Processing (Melt) Temp	270 - 300	°C

Injection instructions
Zone 4: 170 to 200°C

Note Message
1 .	50 mm/min
2 .	50 mm/min
3 .	Tested on 5mm rotomoulded product

Resin Grade	Manufacturer	Category	Trademark
SEETEC PP H7525	LG Chem Ltd.	PP Homopolymer	SEETEC PP
Tecodur® PB70 GR15 BK002 XA21	Eurotec Engineering Plastics	PBT+PET	Tecodur®
DAPCO™ 3008	Cytec Industries Inc.	Epoxy	DAPCO™
INLUBE PA6GF30TF15	Infinity LTL Engineered Compounds	Nylon 6	INLUBE
EPALINE 392A11	Epaflex Polyurethanes S.R.L.	TPU-Polyester	EPALINE