Order Products : sales@su-jiao.com
tefabloc® TP SD 333 40A
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | Mitsubishi Chemical Performance Polymers, Inc. |
| Trademark: | tefabloc® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | KdgcQr_tefabloc-TP-SD-333-40A.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
tefabloc®TP SD 333 40A is a thermoplastic elastomer (TPE) material,. This product is available in North America or Europe. The processing method is injection molding. tefabloc®The main features of TP SD 333 40A are:
Typical application areas include:
|
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| RoHS Compliance |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Resin ID (ISO 1043) |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.15 | g/cm³ | ISO 1183 |
| Melt Mass-Flow Rate (MFR) (190°C/2.16 kg) | 16 | g/10 min | ISO 1133 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 15 sec, Injection Molded) | 39 | ISO 868 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress | ISO 37 | ||
| 20% strain | 0.600 | MPa | ISO 37 |
| 100% strain | 1.00 | MPa | ISO 37 |
| Tensile Stress (Break) | 2.40 | MPa | ISO 37 |
| Tensile Elongation (Break) | 900 | % | ISO 37 |
| Tear Strength 1 | 14 | kN/m | ISO 34-1 |
| Compression Set 2(23°C, 72 hr) | 25 | % | ISO 815 |
| Aging | Nominal Value | Unit | |
|---|---|---|---|
| Resistance to Aging | 110 | °C |
| Thermal | Nominal Value | Unit | |
|---|---|---|---|
| Service Temperature | -50 - 100 | °C |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Rear Temperature | 160 | °C | |
| Middle Temperature | 170 | °C | |
| Front Temperature | 180 | °C | |
| Injection Rate | Moderate | ||
| Screw Compression Ratio | 2.5:1.0 - 3.0:1.0 |
| Injection instructions |
|---|
| Screw Speed: Medium |
| Note Message | |
|---|---|
| 1 . | Method B, right-angle specimen (without cut) |
| 2 . | Type B |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Maxxam™ NM-718.G002-1704 | PolyOne Corporation | PP, Unspecified | Maxxam™ |
| SHIN-A SEV-3475 | SHIN-A T&C | Epoxy | SHIN-A |
| Vi-Chem PVC V142-70I | Vi-Chem Corporation | PVC, Flexible | Vi-Chem PVC |
| Diamond ABS 3001MC | Network Polymers, Inc. | ABS | Diamond ABS |
| Plaslube® PA6/6 GF15 ML3 | Techmer Engineered Solutions | Nylon 66 | Plaslube® |
