Order Products : sales@su-jiao.com
Dapol® D2500F
| Category: | DAP , Diallyl Phthalate |
| Manufacturer: | Fudow Co., Ltd. |
| Trademark: | Dapol® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | Hag47Q_DapolD2500F.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
Examples of application
|
| General Information | |
|---|---|
| Uses |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.80 - 1.90 | g/cm³ | JIS K6911 |
| Molding Shrinkage | JIS K6911 | ||
| -- 1 | 0.60 - 0.80 | % | JIS K6911 |
| -- 2 | 0.40 - 0.60 | % | JIS K6911 |
| Water absorption rate- boiling | 0.10 - 0.20 | % | JIS K6911 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Heat Deflection Temperature | 160 - 180 | °C | JIS K6911 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Insulation Resistance | JIS K6911 | ||
| after boiling | 1.0E+13 - 1.0E+15 | ohms | JIS K6911 |
| at ordinary state | 1.0E+14 - 1.0E+15 | ohms | JIS K6911 |
| Additional Information | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Heat Shrinkage | 0.050 - 0.10 | % | JIS K6918 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Flexural Stress | JIS K6911 | ||
| Molding | 69.0 - 98.0 | MPa | JIS K6911 |
| Injection Molding | 78.0 - 137 | MPa | JIS K6911 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Charpy Notched Impact Strength | JIS K6911 | ||
| Molding | 2.9 - 4.9 | kJ/m² | JIS K6911 |
| Injection Molding | 3.4 - 5.4 | kJ/m² | JIS K6911 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Dielectric Strength | 12 - 16 | kV/mm | JIS K6911 |
| Dielectric Constant | 4.30 - 4.60 | JIS K6911 | |
| Dissipation Factor | 0.010 - 0.015 | JIS K6911 | |
| Arc Resistance | > 130 | sec | JIS K6911 |
| Comparative Tracking Index | > 600 | V | IEC 60112 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Flame Rating (1.0 mm) | V-0 | UL 94 |
| Note Message | |
|---|---|
| 1 . | Injection Molding |
| 2 . | Compression Molding |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| POLYshine PBT D611 | Polykemi AB | PBT | POLYshine |
| RJM SB302 | RJM International, Inc. | PBT | RJM |
| Witcom PEEK 4L1 | Witcom Engineering Plastics B.V. | PEEK | Witcom PEEK |
| AlphaSeal™ 388 D | AlphaGary | TPE | AlphaSeal™ |
| Edgetek™ PC-10GF/000 BLK007 | PolyOne Corporation | PC | Edgetek™ |
