Order Products : sales@su-jiao.com
Akulon® Ultraflow K-FHG6/B
| Category: | Nylon 6 , Polyamide 6 |
| Manufacturer: | DSM Engineering Plastics |
| Trademark: | Akulon® Ultraflow |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | DNqNyq_AkulonUltraflowKFHG6B.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Akulon®Ultraflow K-FHG6/B is a polyamide 6 (nylon 6) material, which contains a 30% glass fiber reinforced material. This product is available in the Asia-Pacific region,. Akulon®The main features of Ultraflow K-FHG6/B are:
|
| General Information | |
|---|---|
| Filler / Reinforcement |
|
| Additive |
|
| Features |
|
| Forms |
|
| Physical | Dry | Conditioned | Unit | Test Method |
|---|---|---|---|---|
| Density | 1.35 | -- | g/cm³ | ISO 1183 |
| Molding Shrinkage | ISO 294-4 | |||
| Transverse flow | 1.1 | -- | % | ISO 294-4 |
| Flow | 0.30 | -- | % | ISO 294-4 |
| Water Absorption | ISO 62 | |||
| Saturated, 23°C | 6.0 | -- | % | ISO 62 |
| Equilibrium, 23°C, 50% RH | 1.8 | -- | % | ISO 62 |
| Mechanical | Dry | Conditioned | Unit | Test Method |
|---|---|---|---|---|
| Tensile Modulus | 9350 | 5700 | MPa | ISO 527-2 |
| Tensile Stress (Break) | 160 | 105 | MPa | ISO 527-2 |
| Tensile Strain (Break) | 3.0 | 7.0 | % | ISO 527-2 |
| Flexural Modulus | 8500 | -- | MPa | ISO 178 |
| Flexural Stress | 235 | -- | MPa | ISO 178 |
| Impact | Dry | Conditioned | Unit | Test Method |
|---|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | |||
| -30°C | 10 | 10 | kJ/m² | ISO 179/1eA |
| 23°C | 14 | 22 | kJ/m² | ISO 179/1eA |
| Charpy Unnotched Impact Strength | ISO 179/1eU | |||
| -30°C | 65 | 65 | kJ/m² | ISO 179/1eU |
| 23°C | 85 | 90 | kJ/m² | ISO 179/1eU |
| Thermal | Dry | Conditioned | Unit | Test Method |
|---|---|---|---|---|
| Heat Deflection Temperature | ||||
| 0.45 MPa, not annealed | 220 | -- | °C | ISO 75-2/B |
| 1.8 MPa, not annealed | 200 | -- | °C | ISO 75-2/A |
| Melting Temperature 1 | 220 | -- | °C | ISO 11357-3 |
| Linear thermal expansion coefficient | ISO 11359-2 | |||
| Flow | 2.0E-5 | -- | cm/cm/°C | ISO 11359-2 |
| Lateral | 7.0E-5 | -- | cm/cm/°C | ISO 11359-2 |
| Electrical | Dry | Conditioned | Unit | Test Method |
|---|---|---|---|---|
| Surface Resistivity | -- | 1.0E+13 | ohms | IEC 60093 |
| Volume Resistivity | > 1.0E+15 | 1.0E+14 | ohms·cm | IEC 60093 |
| Relative Permittivity | IEC 60250 | |||
| 100 Hz | 3.50 | 14.0 | IEC 60250 | |
| 1 MHz | 3.30 | 5.00 | IEC 60250 | |
| Dissipation Factor | IEC 60250 | |||
| 100 Hz | 5.0E-3 | 0.30 | IEC 60250 | |
| 1 MHz | 0.015 | 0.12 | IEC 60250 | |
| Comparative Tracking Index | -- | 500 | V | IEC 60112 |
| Flammability | Dry | Conditioned | Unit | Test Method |
|---|---|---|---|---|
| Flammability Classification (1.6 mm) | HB | -- | IEC 60695-11-10, -20 |
| Injection | Dry | Unit | |
|---|---|---|---|
| Drying Temperature | 80 | °C | |
| Drying Time | 4.0 - 8.0 | hr | |
| Rear Temperature | 230 - 250 | °C | |
| Middle Temperature | 230 - 260 | °C | |
| Front Temperature | 230 - 260 | °C | |
| Nozzle Temperature | 250 - 280 | °C | |
| Processing (Melt) Temp | 245 - 270 | °C | |
| Mold Temperature | 40 - 80 | °C | |
| Injection Rate | Moderate-Fast | ||
| Back Pressure | 3.00 - 10.0 | MPa | |
| Screw Compression Ratio | 2.5:1.0 |
| Note Message | |
|---|---|
| 1 . | 10°C/min |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Ming Dih EPS FS | Ming Dih Group Corporation | PS (EPS) | Ming Dih EPS |
| Yanshan PE 2F0.4A-1 | SINOPEC Beijing Yanshan Petrochemical | LDPE | Yanshan PE |
| Nordbak Backing Material | Loctite® | Epoxy | Nordbak |
| LNP™ LUBRICOMP™ RFL34 compound | SABIC Innovative Plastics | Nylon 66 | LNP™ LUBRICOMP™ |
| PermaFlex® 50 | RAUH Polymers, Inc. | TPE | PermaFlex® |
