Order Products : sales@su-jiao.com
Amodel® A-4122 HR WH 117
| Category: | PPA , Polyphthalamide |
| Manufacturer: | Solvay Specialty Polymers |
| Trademark: | Amodel® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | CEM2CW_Amodel-A-4122-HR-WH-117.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| HR AMODEL A- 4122 resin is 22% glass fiber reinforced polyphthalamide (PPA) to obtain high crystallinity during water-cooled mold molding. The material has high heat resistance, high strength, high rigidity, low moisture absorption, excellent chemical resistance and excellent electrical properties over a wide temperature range. Rapid crystallization and high fluidity can shorten the processing cycle, improve the molding efficiency and reduce part of the cost. -white: A- 4122 HR WH117 |
| General Information | |
|---|---|
| Filler / Reinforcement |
|
| Features |
|
| Uses |
|
| RoHS Compliance |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.50 | g/cm³ | ISO 1183/A |
| Molding Shrinkage | ASTM D955 | ||
| Flow | 0.40 | % | ASTM D955 |
| Transverse flow | 0.60 | % | ASTM D955 |
| Water Absorption (24 hr) | 0.24 | % | ASTM D570 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness (R-Scale) | 124 | ASTM D785 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus | 9100 | MPa | ISO 527-2 |
| Tensile Stress (Yield) | 125 | MPa | ISO 527-2 |
| Tensile Strain (Break) | 1.5 | % | ISO 527-2 |
| Flexural Modulus | 7790 | MPa | ISO 178 |
| Flexural Stress | 171 | MPa | ISO 178 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Notched Izod Impact | |||
| -- | 27 | J/m | ASTM D256 |
| -- | 2.5 | kJ/m² | ISO 180/1A |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Heat Deflection Temperature (0.45 MPa, Unannealed) | 318 | °C | ISO 75-2/B |
| Melting Temperature | 321 | °C | ISO 11357-3 |
| Linear thermal expansion coefficient | ASTM E831 | ||
| Flow : 0 to 100°C | 3.1E-5 | cm/cm/°C | ASTM E831 |
| Flow : 150 to 250°C | 1.4E-5 | cm/cm/°C | ASTM E831 |
| Lateral : 0 to 100°C | 7.4E-5 | cm/cm/°C | ASTM E831 |
| Lateral : 150 to 250°C | 1.6E-4 | cm/cm/°C | ASTM E831 |
| Additional Information | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Light reflectivity 1 | > 90 | % | ASTM E1331 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 120 | °C | |
| Drying Time | 4.0 | hr | |
| Suggested Max Moisture | 0.045 | % | |
| Rear Temperature | 304 - 318 | °C | |
| Front Temperature | 316 - 329 | °C | |
| Processing (Melt) Temp | 321 - 343 | °C | |
| Mold Temperature | 135 | °C |
| Injection instructions |
|---|
| Storage: Amodel® compounds are shipped in moisture-resistant packages at moisture levels according to specifications. Sealed, undamaged bags should be preferably stored in a dry room at a maximum temperature of 50°C (122°F) and should be protected from possible damage. If only a portion of a package is used, the remaining material should be transferred into a sealable container. It is recommended that Amodel® resins be dried prior to molding following the recommendations found in this datasheet and/or in the Amodel® processing guide. |
| Note Message | |
|---|---|
| 1 . | 430 - 700 nm |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Propafilm™ RF120 | Innovia Films Ltd. | PP Alloy | Propafilm™ |
| Chiao Fu PA66/6 MB312G33 BK | Chiao Fu Enterprises Co., Ltd. | Nylon 66/6 | Chiao Fu PA66/6 |
| KOCETAL® CF702 | Kolon Plastics, Inc. | Acetal (POM) Copolymer | KOCETAL® |
| LAPEROS® C400 | Polyplastics Co., Ltd. | LCP | LAPEROS® |
| GELOY™ EXGY0058 resin | SABIC Innovative Plastics | ASA+PC | GELOY™ |
