Duratron® T4203 (EXTRUSION) Datasheet,PAI,Quadrant Engineering Plastic Products-SHANGHAI SUSHENG

Duratron® T4203 (EXTRUSION)

Wechat: WECHAT

Message
Duratron® T4203 extruded PAI offers excellent compressive strength and the highest elongation of the Duratron® PAI grades. It also provides electrical insulation and exceptional impact strength. This grade is commonly used for electrical connectors and insulators due to its high dielectric strength. Duratron® PAI is the highest performing melt processable plastic. It has superior resistance to elevated temperatures. It is capable of performing under severe stress conditions at continuous temperatures to 500°F (260°C). Parts machined from Duratron® PAI stock shapes provide greater compressive strength and higher impact resistance than most advanced engineering plastics. Its extremely low coefficient of linear thermal expansion and high creep resistance deliver excellent dimensional stability over its entire use range. Duratron® is an amorphous material with a Tg (glass transition temperature) of 537°F (280°C). Quadrant EPP's extruded Duratron® stock shapes are post-cured using the latest technology and procedures developed jointly by Amoco Performance Products and Quadrant eliminating the need for additional curing by the end user in most situations. A post-curing cycle is recommended for components fabricated from extruded shapes where optimization of chemical resistance and/or wear performance is required. Data provided by Quadrant Engineering Plastic Products from tests on stock shapes and parts produced by Quadrant EPP.

Message

Duratron® T4203 extruded PAI offers excellent compressive strength and the highest elongation of the Duratron® PAI grades. It also provides electrical insulation and exceptional impact strength. This grade is commonly used for electrical connectors and insulators due to its high dielectric strength.

Duratron® PAI is the highest performing melt processable plastic. It has superior resistance to elevated temperatures. It is capable of performing under severe stress conditions at continuous temperatures to 500°F (260°C). Parts machined from Duratron® PAI stock shapes provide greater compressive strength and higher impact resistance than most advanced engineering plastics. Its extremely low coefficient of linear thermal expansion and high creep resistance deliver excellent dimensional stability over its entire use range. Duratron® is an amorphous material with a Tg (glass transition temperature) of 537°F (280°C).

Quadrant EPP's extruded Duratron® stock shapes are post-cured using the latest technology and procedures developed jointly by Amoco Performance Products and Quadrant eliminating the need for additional curing by the end user in most situations. A post-curing cycle is recommended for components fabricated from extruded shapes where optimization of chemical resistance and/or wear performance is required.

Data provided by Quadrant Engineering Plastic Products from tests on stock shapes and parts produced by Quadrant EPP.

General Information
Features	Acid Resistant Alcohol Resistant Alkali Resistant Amorphous Electrically Insulating Good Chemical Resistance Good Compressive Strength Good Creep Resistance Good Stiffness Good Thermal Stability Good Wear Resistance High Strength Hydrocarbon Resistant Low Friction Solvent Resistant
Uses	Bearings Bushings Electrical Parts Pump Parts Sealing Devices Seals
Forms	Customizable Forms Preformed Parts Profiles Rod Sheet Tubing
Processing Method	Extrusion

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.41	g/cm³	ASTM D792
Water Absorption			ASTM D570
24 hr	0.40	%
Saturation	1.7	%

Hardness	Nominal Value	Test Method
Rockwell Hardness		ASTM D785
E-Scale	80
M-Scale	120

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus	4140	MPa	ASTM D638
Tensile Strength (Ultimate)	138	MPa	ASTM D638
Tensile Elongation (Break)	10	%	ASTM D638
Flexural Modulus	4140	MPa	ASTM D790
Flexural Strength (Yield)	165	MPa	ASTM D790
Compressive Modulus	3300	MPa	ASTM D695
Compressive Strength (10% Strain)	165	MPa	ASTM D695
Shear Strength	110	MPa	ASTM D732
Coefficient of Friction (vs. Steel - Static)	0.35		Internal Method
Wear Factor	> 2000	10^-8 mm³/N·m	ASTM D3702

Impact	Nominal Value	Unit	Test Method
Notched Izod Impact	110	J/m	ASTM D256A

Thermal	Nominal Value	Unit	Test Method
Deflection Temperature Under Load (1.8 MPa, Unannealed)	278	°C	ASTM D648
Maximum Use Temperature - Long Term, Air	260	°C

Additional Information	Nominal Value	Unit	Test Method
Limiting Pressure Velocity ¹	0.140	MPa·m/s	Internal Method

Thermal	Nominal Value	Unit	Test Method
Glass Transition Temperature	275	°C	ASTM D3418
CLTE - Flow ²(-40 to 149°C)	3.1E-5	cm/cm/°C	ASTM E831
Thermal Conductivity	0.26	W/m/K	ASTM F433

Electrical	Nominal Value	Unit	Test Method
Surface Resistivity ³	> 1.0E+16	ohms	Internal Method
Dielectric Strength ⁴	23	kV/mm	ASTM D149
Dielectric Constant (1 MHz)	4.20		ASTM D150
Dissipation Factor (1 MHz)	0.026		ASTM D150

Flammability	Nominal Value	Unit	Test Method
Flame Rating (3.18 mm, Estimated Rating)	V-0		UL 94

Note Message
1 .	4:1 safety factor
2 .	68°F
3 .	EOS/ESD S11.11
4 .	Method A (Short-Time)

Resin Grade	Manufacturer	Category	Trademark
Ad-Tech Epoxy EC-405 (45R/55H)	Ad-Tech Plastic Systems Corp.	Epoxy	Ad-Tech Epoxy
Fainplast PVC KL 96	Fainplast Compounds S.r.l	PVC, Unspecified	Fainplast PVC
Grivory® GV-5H EF black 9915	EMS-GRIVORY	Nylon 66+Nylon 6I/X	Grivory®
MAJORIS DFR218	AD majoris	PP, Unspecified	MAJORIS
Sylvin 5132-86 Clear Blue 8376	Sylvin Technologies Incorporated	PVC, Unspecified	Sylvin

Resin Grade

Manufacturer

Category:	PAI , Polyamide-imide
Manufacturer:	Quadrant Engineering Plastic Products
Trademark:	Duratron®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	BGgrG7_Duratron-T4203-EXTRUSION-.pdf
PRICE:	Order Products email sales@su-jiao.com