Beetle® PBTS830F Datasheet,PBT,Teknor Apex Company (Chem Polymer)-SHANGHAI SUSHENG

Message
PBTS830F is a flame retarded 30% glass fibre filled PBT moulding grade that achieves V0 classification and displays good mechanical performance. It contains a RoHS permissible Brominated FR system.

General Information
Filler / Reinforcement	Glass fiber reinforced material, 30% filler by weight
Additive	Flame retardancy 2
Features	Flame retardancy
Processing Method	Injection molding

Physical	Nominal Value	Unit	Test Method
Density	1.71	g/cm³	ISO 1183
Molding Shrinkage ¹	0.80 - 1.4	%	Internal method

Mechanical	Nominal Value	Unit	Test Method
Tensile Stress (Break)	130	MPa	ISO 527-2
Tensile Strain (Break)	2.0	%	ISO 527-2
Flexural Modulus	9000	MPa	ISO 178
Flexural Stress ²	160	MPa	ISO 178

Impact	Nominal Value	Unit	Test Method
Notched Izod Impact	6.5	kJ/m²	ISO 180

Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature
0.45 MPa, not annealed	> 200	°C	ISO 75-2/B
1.8 MPa, not annealed	190	°C	ISO 75-2/A

Electrical	Nominal Value	Unit	Test Method
Surface Resistivity	1.0E+15	ohms	IEC 60093
Volume Resistivity	1.0E+17	ohms·cm	IEC 60093
Dielectric Strength (3.00 mm)	15	kV/mm	IEC 60243-1
Comparative Tracking Index	300	V	IEC 60112

Flammability	Nominal Value	Unit	Test Method
Flame Rating (1.50 mm)	V-0		Internal method
Glow Wire Flammability Index (1.50 mm)	960	°C	IEC 60695-2-12
Oxygen Index	38	%	ISO 4589-2

Injection	Nominal Value	Unit
Drying Temperature	120	°C
Drying Time	4.0	hr
Rear Temperature	240 - 260	°C
Middle Temperature	240 - 260	°C
Front Temperature	240 - 260	°C
Processing (Melt) Temp	< 270	°C
Mold Temperature	70.0 - 90.0	°C
Injection Rate	Moderate
Screw Speed	50 - 200	rpm

Injection instructions
Back pressure: LowInjection pressure: HighPBT materials are hygroscopic and very sensitive to moisture content during processing. Unlike many other materials, excessive moisture may not give rise to the appearance of splash marks on the surface of mouldings, but hydrolytic degradation of the melt can lead to significant impairment of properties, characterised most noticeably by embrittlement of the mouldings and reduced melt viscosity. Adequate pre-drying is therefore essential.Drying should ideally be carried out in a vacuum oven or a dehumidified air drier. The recommended drying time for dehumidified air dryers is 4 hours at 120°C. Drying times may need to be extended if the material has become very wet.

Injection instructions

Back pressure: LowInjection pressure: HighPBT materials are hygroscopic and very sensitive to moisture content during processing. Unlike many other materials, excessive moisture may not give rise to the appearance of splash marks on the surface of mouldings, but hydrolytic degradation of the melt can lead to significant impairment of properties, characterised most noticeably by embrittlement of the mouldings and reduced melt viscosity. Adequate pre-drying is therefore essential.Drying should ideally be carried out in a vacuum oven or a dehumidified air drier. The recommended drying time for dehumidified air dryers is 4 hours at 120°C. Drying times may need to be extended if the material has become very wet.

Note Message
1 .	Mould shrinkage is significantly influenced by many factors including wall thickness, gating, component shape and moulding conditions.The range values stated were determined from specimen bar mouldings of 1.5mm to 4mm wall thickness. They are provided as a guide for comparison purposes only and no guarantee should be inferred from their inclusion. (Specimens measured in the dry state, 24 hours after moulding).
2 .	Break

Note Message

1 .

Mould shrinkage is significantly influenced by many factors including wall thickness, gating, component shape and moulding conditions.The range values stated were determined from specimen bar mouldings of 1.5mm to 4mm wall thickness. They are provided as a guide for comparison purposes only and no guarantee should be inferred from their inclusion. (Specimens measured in the dry state, 24 hours after moulding).

2 .

Break

Category:	PBT , Polybutylene Terephthalate
Manufacturer:	Teknor Apex Company (Chem Polymer)
Trademark:	Beetle®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	AbG3m1_Beetle-PBTS830F.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
MAXAMID™ PA6G13-BK10	Pier One Polymers, Inc.	Nylon 6	MAXAMID™
Aplax P0413GN	Ginar Technology Co., LTD.	PP, Unspecified	Aplax
Karina IVORY PVC COMPOUND -E 857-35/ 1-DY-IS(VS-80)/K	Karina Ind. e Com. de Plásticos Ltda	PVC, Unspecified	Karina
MAJORIS DG407X - 8784	AD majoris	PP, Unspecified	MAJORIS
LEXAN™ 243R resin	SABIC Innovative Plastics	PC	LEXAN™