Order Products : sales@su-jiao.com
China PPS PTFE-hGR312
| Category: | PPS , Polyphenylene Sulfide |
| Manufacturer: | Sichuan Deyang Chemical Co., Ltd |
| Trademark: | China PPS |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | 9ZEM1F_China-PPS-PTFE-hGR312.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
PPS/PTFE-hGR312 is lubricant PPS compound, which is filled with glass fiber, PTFE and ingredients based on the PPS resin. It shows abrasive resistance, solvent resistance and good mechanic prosperity, high modulus, creep resistance, high-temperature resistance, inherent flame resistance, easy processing, low mold shrinkage. Owing to its high performance, it's widely used in chemical and medical industry for making wearing pieces in corrosive solvent condition of high temperature, high pressure and corrosive solvent. It also can be used to make plastic axle sleeve, axle bearing and slide block in mechanical industry. |
| General Information | |
|---|---|
| Filler / Reinforcement |
|
| Additive |
|
| Features |
|
| Uses |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.55 | g/cm³ | Internal method |
| Molding Shrinkage - Flow | 0.25 | % | Internal method |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness 1 | 100 | Internal method |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Strength | 115 | MPa | Internal method |
| Tensile Elongation (Break) | 1.7 | % | Internal method |
| Flexural Modulus | 8400 | MPa | Internal method |
| Flexural Strength | 164 | MPa | Internal method |
| Coefficient of Friction | 0.21 | Internal method | |
| Abrasion - Width | 7 | mm | Internal method |
| Abrasion Loss 2 | 4.1 | mg | Internal method |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Notched Izod Impact | 8.6 | kJ/m² | Internal method |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load (1.8 MPa, Unannealed) | 265 | °C | Internal method |
| Melting Temperature | 281 | °C | Internal method |
| Flammability | Nominal Value | Test Method | |
|---|---|---|---|
| Flame Rating | V-0 | Internal method |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 110 - 140 | °C | |
| Drying Time | 3.0 - 5.0 | hr | |
| Rear Temperature | 270 - 290 | °C | |
| Middle Temperature | 300 - 320 | °C | |
| Front Temperature | 300 - 320 | °C | |
| Nozzle Temperature | 290 - 320 | °C | |
| Processing (Melt) Temp | 160 | °C | |
| Mold Temperature | 100 - 150 | °C | |
| Injection Pressure | 50.0 - 100 | MPa | |
| Back Pressure | 0.100 - 1.00 | MPa | |
| Screw Speed | 40 - 100 | rpm |
| Injection instructions |
|---|
| Processing time: 2 to 8hr |
| Note Message | |
|---|---|
| 1 . | HR |
| 2 . | 120 min |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| RTP 4487 | RTP Company | Nylon, Unspecified | RTP |
| SCANAMID 66 A33^E F45 | Polykemi AB | Nylon 66 | SCANAMID 66 |
| Plexar® PX2250 | LyondellBasell Industries | HDPE | Plexar® |
| Plenco 01510 (Injection) | Plastics Engineering Co. | Polyester, TS | Plenco |
| TORZEN® G3300L NC01 | INVISTA Engineering Polymers | Nylon 66 | TORZEN® |
