Order Products : sales@su-jiao.com
Generic Nylon 66 - Glass Fiber
| Category: | Nylon 66 , Polyamide 66 |
| Manufacturer: | Generic |
| Trademark: | Generic |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | 8ZBGhO_Generic-Nylon-66---Glass-Fiber.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
This data represents typical values that have been calculated from all products classified as: Generic Nylon 66 - Glass Fiber This information is provided for comparative purposes only. |
| General Information | |
|---|---|
| Filler / Reinforcement |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | |||
| -- | 1.17 - 1.62 | g/cm³ | ASTM D792 |
| 23°C | 1.23 - 1.58 | g/cm³ | ISO 1183 |
| -- | 1360 | kg/m³ | ISO 1183 1 |
| -- | 1.20 - 1.73 | g/cm³ | ASTM D1505 |
| Apparent Density | 0.70 | g/cm³ | ISO 60 |
| Melt Mass-Flow Rate (MFR) | |||
| 275°C/2.16 kg | 4.0 - 25 | g/10 min | ASTM D1238 |
| 275°C/0.325 kg | 1.0 - 3.1 | g/10 min | ISO 1133 |
| Melt Volume-Flow Rate (MVR) (275°C/5.0 kg) | 18.8 - 51.2 | cm³/10min | ISO 1133 |
| Spiral Flow | 53.0 - 99.6 | cm | |
| Molding Shrinkage | |||
| Flow : 23°C | 0.19 - 0.75 | % | ASTM D955 |
| Transverse flow : 23°C | 0.40 - 2.0 | % | ASTM D955 |
| 23°C | 0.19 - 1.2 | % | ISO 294-4 |
| Water Absorption | |||
| 23°C, 24 hr | 0.43 - 1.0 | % | ASTM D570 |
| 23°C, 24 hr | 0.43 - 1.3 | % | ISO 62 |
| Saturated, 23°C | 0.10 - 7.2 | % | ASTM D570 |
| Saturated, 23°C | 3.9 - 7.0 | % | ISO 62 |
| Saturation | 5.5 | % | ISO 62 2 |
| Equilibrium, 23°C | 0.30 - 2.3 | % | ASTM D570 |
| Equilibrium, 23°C, 50% RH | 1.1 - 2.3 | % | ISO 62 |
| Balance | 1.6 | % | ISO 62 3 |
| Viscosity Number | |||
| -- | 129 - 151 | cm³/g | ISO 307 |
| -- | 143 | cm³/g | ISO 307, 1157, 1628 4 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness | |||
| 23°C | 114 - 124 | ASTM D785 | |
| 23°C | 95 - 122 | ISO 2039-2 | |
| Durometer Hardness | |||
| 23°C | 73 - 122 | ASTM D2240 | |
| 23°C | 78 - 90 | ISO 868 | |
| Ball Indentation Hardness | 188 - 262 | MPa | ISO 2039-1 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus | |||
| 23°C | 3850 - 13400 | MPa | ASTM D638 |
| 23°C | 4510 - 13500 | MPa | ISO 527-2 |
| -- | 8160 | MPa | ISO 527-2 5 |
| Tensile Strength | |||
| Yield, 23°C | 58.8 - 253 | MPa | ASTM D638 |
| Yield, 23°C | 78.9 - 232 | MPa | ISO 527-2 |
| Fracture, 23°C | 74.4 - 222 | MPa | ASTM D638 |
| Fracture, 23°C | 87.7 - 253 | MPa | ISO 527-2 |
| Fracture | 160 | MPa | ISO 527-2 6 |
| Limit, 23°C | 75.8 - 200 | MPa | ASTM D638 |
| 23°C | 80.8 - 214 | MPa | ASTM D638 |
| 23°C | 70.8 - 192 | MPa | ISO 527-2 |
| Tensile Elongation | |||
| Yield, 23°C | 2.4 - 3.7 | % | ASTM D638 |
| Yield, 23°C | 1.9 - 3.6 | % | ISO 527-2 |
| Fracture, 23°C | 1.0 - 700 | % | ASTM D638 |
| Fracture, 23°C | 1.7 - 4.2 | % | ISO 527-2 |
| Fracture | 2.5 - 3.1 | % | ISO 527-2 7 |
| Flexural Modulus | |||
| 23°C | 2240 - 11200 | MPa | ASTM D790 |
| 23°C | 3500 - 12600 | MPa | ISO 178 |
| Flexural Strength | |||
| 23°C | 108 - 334 | MPa | ASTM D790 |
| 23°C | 144 - 323 | MPa | ISO 178 |
| Yield, 23°C | 138 - 294 | MPa | ASTM D790 |
| Fracture, 23°C | 126 - 338 | MPa | ASTM D790 |
| Compressive Strength | |||
| 23°C | 94.0 - 251 | MPa | ASTM D695 |
| 23°C | 28.0 - 195 | MPa | ISO 604 |
| Shear Strength (23°C) | 68.5 - 105 | MPa | ASTM D732 |
| Coefficient of Friction | 0.16 - 0.67 | ASTM D1894 | |
| Wear Factor | 33 - 160 | 10^-8 mm³/N·m | ASTM D3702 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23°C | 57.0 - 118 | J/m | ASTM D256 |
| 23°C | 5.0 - 18 | kJ/m² | ISO 179 |
| -30°C | 6.60 | kJ/m² | ISO 179/1eA 8 |
| 23°C | 7.89 | kJ/m² | ISO 179/1eA 9 |
| Charpy Unnotched Impact Strength | |||
| 23°C | 27 - 100 | kJ/m² | ISO 179 |
| -30°C | 60.0 | kJ/m² | ISO 179/1eU 10 |
| 23°C | 65.5 | kJ/m² | ISO 179/1eU 11 |
| Notched Izod Impact | |||
| 23°C | 32 - 170 | J/m | ASTM D256 |
| 23°C | 3.0 - 17 | kJ/m² | ISO 180 |
| Notched Izod Impact (23°C) | 4.42 - 11.2 | kJ/m² | ASTM D256 |
| Unnotched Izod Impact | |||
| 23°C | 310 - 1400 | J/m | ASTM D256 |
| 23°C | 28 - 92 | kJ/m² | ISO 180 |
| Instrumented Dart Impact | |||
| 23°C | 5.36 - 18.2 | J | ASTM D3763 |
| 23°C | 1.64 - 4.06 | J | ISO 6603-2 |
| Multi-Axial Instrumented Impact Peak Force (23°C) | 610 - 1160 | N | ISO 6603-2 |
| Tensile Impact Strength (23°C) | 11.3 - 430 | kJ/m² | ASTM D1822 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load | |||
| 0.45 MPa, not annealed | 240 - 264 | °C | ASTM D648 |
| 0.45 MPa, not annealed | 240 - 261 | °C | ISO 75-2/B |
| 0.45 MPa | 250 | °C | ISO 75-2 12 |
| 1.8 MPa, not annealed | 231 - 255 | °C | ASTM D648 |
| 1.8 MPa, not annealed | 226 - 260 | °C | ISO 75-2/A |
| 1.8 MPa | 250 | °C | ISO 75-2 13 |
| 8.0 MPa, not annealed | 70.0 - 235 | °C | ISO 75-2/C |
| Continuous Use Temperature | 85.2 - 181 | °C | ASTM D794 |
| Glass Transition Temperature | 79.9 - 80.0 | °C | ISO 11357-2 |
| Vicat Softening Temperature | |||
| -- | 239 - 256 | °C | ASTM D1525 |
| -- | 200 - 256 | °C | ISO 306 |
| Melting Temperature | |||
| -- | 248 - 266 | °C | |
| -- | 259 - 260 | °C | DSC |
| -- | 255 - 263 | °C | ISO 11357-3 |
| -- | 254 - 261 | °C | ASTM D3418 |
| -- | 260 | °C | ISO 3146 |
| Linear thermal expansion coefficient | |||
| Flow | 2.0E-6 - 6.2E-5 | cm/cm/°C | ASTM D696 |
| Flow | 8.9E-6 - 3.9E-5 | cm/cm/°C | ASTM E831 |
| Flow | 1.1E-5 - 4.1E-5 | cm/cm/°C | ISO 11359-2 |
| Lateral | 1.0E-6 - 8.6E-5 | cm/cm/°C | ASTM D696 |
| Lateral | 1.6E-5 - 1.3E-4 | cm/cm/°C | ASTM E831 |
| Lateral | 6.0E-5 - 1.0E-4 | cm/cm/°C | ISO 11359-2 |
| Specific Heat (23°C) | 1490 - 1510 | J/kg/°C | ASTM C351 |
| Thermal Conductivity | |||
| 23°C | 0.29 - 0.52 | W/m/K | ASTM C177 |
| 23°C | 0.20 - 0.44 | W/m/K | ISO 8302 |
| RTI Elec | 65.0 - 140 | °C | UL 746 |
| RTI Imp | 65.0 - 140 | °C | UL 746 |
| RTI | 65.0 - 142 | °C | UL 746 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Surface Resistivity | |||
| -- | 2.0 - 2.5E+15 | ohms | ASTM D257 |
| -- | 0.10 - 2.5E+15 | ohms | IEC 60093 |
| Volume Resistivity | |||
| 23°C | 10 - 2.5E+16 | ohms·cm | ASTM D257 |
| 23°C | 10 - 5.0E+16 | ohms·cm | IEC 60093 |
| Dielectric Strength | |||
| 23°C | 17 - 26 | kV/mm | ASTM D149 |
| 23°C | 18 - 90 | kV/mm | IEC 60243-1 |
| Dielectric Constant | |||
| 23°C | 3.49 - 4.05 | ASTM D150 | |
| 23°C | 3.48 - 4.04 | IEC 60250 | |
| 23°C | 7.26 | IEC 60250 | |
| Dissipation Factor | |||
| 23°C | 0.012 - 0.021 | ASTM D150 | |
| 23°C | 4.0E-3 - 0.098 | IEC 60250 | |
| 1 MHz | 0.018 | IEC 60250 14 | |
| Arc Resistance | 109 - 137 | sec | ASTM D495 |
| Comparative Tracking Index (CTI) | 590 - 600 | V | UL 746 |
| Comparative Tracking Index | |||
| -- | 389 - 603 | V | IEC 60112 |
| -- | 443 - 451 | V | ASTM D3638 |
| -- | 500 | IEC 60112 15 | |
| Insulation Resistance (23°C) | 9.8E+11 - 1.0E+12 | ohms | IEC 60167 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Burning Rate | 0.0 - 100 | mm/min | ISO 3795 |
| Glow Wire Flammability Index | 645 - 960 | °C | IEC 60695-2-12 |
| Glow Wire Ignition Temperature | 650 - 961 | °C | IEC 60695-2-13 |
| Oxygen Index | |||
| -- | 23 - 34 | % | ASTM D2863 |
| -- | 23 - 27 | % | ISO 4589-2 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 78.3 - 90.6 | °C | |
| Drying Time | 2.8 - 5.3 | hr | |
| Drying Time, Maximum | 6.0 | hr | |
| Dew Point | -18.1 - -17.8 | °C | |
| Suggested Max Moisture | 0.20 | % | |
| Suggested Shot Size | 55 - 60 | % | |
| Suggested Max Regrind | 22 | % | |
| Hopper Temperature | 70.0 - 285 | °C | |
| Rear Temperature | 265 - 289 | °C | |
| Middle Temperature | 270 - 294 | °C | |
| Front Temperature | 268 - 300 | °C | |
| Nozzle Temperature | 272 - 291 | °C | |
| Processing (Melt) Temp | 274 - 297 | °C | |
| Mold Temperature | 68.4 - 102 | °C | |
| Injection Pressure | 7.02 - 112 | MPa | |
| Holding Pressure | 59.1 - 77.2 | MPa | |
| Back Pressure | 0.0490 - 1.15 | MPa | |
| Screw Speed | 45 - 75 | rpm | |
| Clamp Tonnage | 4.0 - 9.0 | kN/cm² | |
| Cushion | 4.66 - 5.08 | mm | |
| Vent Depth | 0.019 - 0.024 | mm |
| Injection instructions |
|---|
| This data represents typical values that have been calculated from all products classified as: Generic Nylon 66 - Glass FiberThis information is provided for comparative purposes only. |
| Note Message | |
|---|---|
| 1 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 2 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 3 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 4 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 5 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 6 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 7 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 8 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 9 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 10 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 11 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 12 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 13 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 14 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| 15 . | ??????,?? ISO 10350 ??? 23°C/50%r.h. ??? |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| SLOVALEN® PH 56 FRD 1 | Plastcom | PP, Unspecified | SLOVALEN® |
| DENITER 3015 | Vamp Tech | PBT | DENITER |
| Escorene™ Ultra UL 7840E | ExxonMobil Chemical | EVA | Escorene™ Ultra |
| Petrotene® PP A2 T30 PRTA011 PH201 | Petropol Industry and Trade of Polymers LTDA | PP Homopolymer | Petrotene® PP |
| LNP™ STAT-KON™ DX04490 compound | SABIC Innovative Plastics | PC | LNP™ STAT-KON™ |
