Alcryn® 4680 BK Datasheet,MPR,Advanced Polymer Alloys-SHANGHAI SUSHENG

Message
Alcryn®4680 BK is a melt processable rubber (MPR) material,. This product is available in North America, Europe or Asia Pacific. The processing methods are: blow molding, extrusion, compression molding or injection molding. Alcryn®The main features of 4680 BK are: Comply with WEEE standard ROHS certification Good UV resistance good weather resistance chemical resistance Typical application areas include: Wire and cable engineering/industrial accessories Hose sheet textile/fiber

General Information
Additive	UV stabilizer
Features	Shock absorption Noise reduction Good UV resistance Medium liquidity Ozone resistance Good weather resistance Heat resistance, high Oil resistance
Uses	Handle Cable sheath Wire sheath Washer Engineering accessories Pipe Pipe fittings Seals Weather-resistant sealing strip Sheet Fabric
Agency Ratings	EU 2002/96/EC (WEEE)
RoHS Compliance	RoHS compliance
Appearance	Black
Forms	Particle
Processing Method	Blow molding Extrusion Compression molding Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.27	g/cm³	ASTM D792, ISO 1183

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore A, 1.91mm, molded)	79		ASTM D2240
IRHD Hardness	79		ISO 48

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus (1.91mm, molded)	5.93	MPa	ASTM D638, ISO 527-2
Tensile Strength (yield, 1.91mm, molding)	10.8	MPa	ASTM D638, ISO 527-2
Tensile Elongation (fracture, 1.91mm, molded)	380	%	ASTM D638, ISO 527-2
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel)	6.00	mg	ASTM D1044

Elastomers	Nominal Value	Unit	Test Method
Tensile Set	12	%	ASTM D412
Tear Strength ¹(24°C)	52.5	kN/m	ASTM D624
Compression Set			ASTM D395B, ISO 815
24°C, 22 hr	24	%	ASTM D395B, ISO 815
100°C, 22 hr	75	%	ASTM D395B, ISO 815
Clash-Berg Modulus (1°C)	68.9	MPa	ASTM D1043

Aging	Nominal Value	Unit	Test Method
Change in Shore Hardness in Air (125°C, 168 hr)	76		ISO 188
Change in Ultimate Elongation (125°C, 168 hr)	380	%	ASTM D471
Change in Durometer Hardness (125°C, 168 hr)	76		ASTM D471
Change in Volume			ASTM D471
24°C, 168 hr, in reference fuel B	22	%	ASTM D471
100°C, 168 hr, ASTM Standard Oil (No.1)	-9.0	%	ASTM D471
100°C, 168 hr, ASTM Standard Oil (No.3)	24	%	ASTM D471
100°C, 168 hr, in water	10	%	ASTM D471

Thermal	Nominal Value	Unit	Test Method
Brittleness Temperature	-59.4	°C	ASTM D746, ISO 974

Additional Information
The value listed as Density-Specific Gravity, ASTM D792, was tested in accordance with ASTM D471.Torsion Modulus, ASTM D1043, 75°F: 600psiAging Tensile Strength, ASTM D573, 7 days, 257°F: 1600psiTorsion Modulus, ASTM D1043, -4°F: 10000psiAging 100% Modulus, ASTM D573, 7 days, 257 °F: 1100psiAging Elongation At Break, ASTM D573 and ISO 188: 380%Fluid Resistance 7 Days in water, ISO 1817, at 212 °F: 10%Fluid Resistance 7 Days in ASTM Oil no. 1, ISO 1817, at 212 °F: -9%Fluid Resistance 7 Days in IRM 903 Oil no. 3, ISO 1817, at 212 °F: 24%Fluid Resistance 7 Days in ASTM Ref. Fuel no. B, ISO 1817, at 75 °F: 22%Rheological Viscosity, ASTM D3835, 1/300s at 374°F: 780Pa-s

Additional Information

The value listed as Density-Specific Gravity, ASTM D792, was tested in accordance with ASTM D471.Torsion Modulus, ASTM D1043, 75°F: 600psiAging Tensile Strength, ASTM D573, 7 days, 257°F: 1600psiTorsion Modulus, ASTM D1043, -4°F: 10000psiAging 100% Modulus, ASTM D573, 7 days, 257 °F: 1100psiAging Elongation At Break, ASTM D573 and ISO 188: 380%Fluid Resistance 7 Days in water, ISO 1817, at 212 °F: 10%Fluid Resistance 7 Days in ASTM Oil no. 1, ISO 1817, at 212 °F: -9%Fluid Resistance 7 Days in IRM 903 Oil no. 3, ISO 1817, at 212 °F: 24%Fluid Resistance 7 Days in ASTM Ref. Fuel no. B, ISO 1817, at 75 °F: 22%Rheological Viscosity, ASTM D3835, 1/300s at 374°F: 780Pa-s

Injection	Nominal Value	Unit
Processing (Melt) Temp	177	°C

Note Message
1 .	C mould

Category:	MPR , Melt Processable Rubber
Manufacturer:	Advanced Polymer Alloys
Trademark:	Alcryn®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	6N3qof_Alcryn-4680-BK.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
Viprene™ G70A-32U-NAT	Alliance Polymers & Services	TPV	Viprene™
LNP™ STAT-KON™ AE006 compound	SABIC Innovative Plastics	ABS	LNP™ STAT-KON™
Clyrell EC5082	LyondellBasell Industries	PP, Unspecified	Clyrell
Lucon® CP2100	LG Chem Ltd.	PC	Lucon®
VALOX™ 4031 resin	SABIC Innovative Plastics Europe	PBT	VALOX™