Order Products : sales@su-jiao.com

VECTOR® 4113N

Category:	SIS+SI , Styrene Isoprene Styrene + SI Block Copolymer
Manufacturer:	TSRC Corporation
Trademark:	VECTOR®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	6Hypbv_VECTOR-4113N.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

Message
Blend of linear SIS triblock and SI diblock copolymer. Contains ~18% SI diblock copolymer. Low styrene, low modulus. VECTOR 4113A and VECTOR 4113N styrenic block copolymers are blended products composed of a linear SIS triblock copolymer and an SI diblock copolymer. They are softer than VECTOR 4111A SIS/SI due to lower styrene content and presence of diblock copolymer, making them well-suited for use in hot melt pressure sensitive adhesives, elastomer compounds and photopolymer plate applications. VECTOR 4113A SIS/SI is offered as a dense pellet supplied from the United States. VECTOR 4113N SIS/SI is offered as a porous pellet supplied from China.

Message

Blend of linear SIS triblock and SI diblock copolymer.

Contains ~18% SI diblock copolymer.

Low styrene, low modulus.

VECTOR 4113A and VECTOR 4113N styrenic block copolymers are blended products composed of a linear SIS triblock copolymer and an SI diblock copolymer. They are softer than VECTOR 4111A SIS/SI due to lower styrene content and presence of diblock copolymer, making them well-suited for use in hot melt pressure sensitive adhesives, elastomer compounds and photopolymer plate applications.

VECTOR 4113A SIS/SI is offered as a dense pellet supplied from the United States.

VECTOR 4113N SIS/SI is offered as a porous pellet supplied from China.

General Information
Features	Soft
Uses	Adhesives
Forms	Pellets

Physical	Nominal Value	Unit	Test Method
Specific Gravity	0.918	g/cm³	ASTM D792
Apparent Density	0.33	g/cm³	ASTM D1895
Melt Mass-Flow Rate (MFR) (200°C/5.0 kg)	11	g/10 min	ASTM D1238
Bound Styrene	15.0	%
Ash Content	0.3	wt%
Solution Viscosity - in 25 wt% Toluene (25°C)	1.2	Pa·s

Additional Information	Nominal Value	Unit
Diblock Content	18.0	wt%

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore A, 1 sec, Compression Molded)	33		ASTM D2240

Elastomers	Nominal Value	Unit	Test Method
Tensile Stress ¹(300% Strain)	1.10	MPa	Internal Method
Tensile Strength ²(Break)	25.0	MPa	Internal Method
Tensile Elongation ³(Break)	1300	%	Internal Method

Note Message
1 .	Compression Molded
2 .	Compression Molded
3 .	Compression Molded

Resin Grade	Manufacturer	Category	Trademark
SNOLEN® EP 0.26/51 Y	JSC Gazprom neftekhim Salavat	HDPE	SNOLEN®
Verolloy A5732	PlastxWorld Inc.	ABS+Nylon	Verolloy
Network Polymers SMMA MS 170	Network Polymers, Inc.	Acrylic (SMMA)	Network Polymers SMMA
ADDINYL B2 ZV15	ADDIPLAST	Nylon 6	ADDINYL
KOCETAL® WR701LO	Kolon Plastics, Inc.	Acetal (POM) Copolymer	KOCETAL®