Order Products : sales@su-jiao.com
SCHULATEC® PP EC 1009 HI BLACK
| Category: | PP Copolymer , Polypropylene Copolymer |
| Manufacturer: | A. Schulman Europe |
| Trademark: | SCHULATEC® |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | 5a8Qzd_SCHULATEC-PP-EC-1009-HI-BLACK.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| PP electrical conductive, high impact |
| General Information | |
|---|---|
| Processing Method |
|
| Resin ID (ISO 1043) |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 1.11 | g/cm³ | ISO 1183/A |
| Melt Volume-Flow Rate (MVR) | ISO 1133 | ||
| 230°C/10.0 kg | 35.0 | cm³/10min | ISO 1133 |
| 230°C/2.16 kg | 0.300 | cm³/10min | ISO 1133 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Ball Indentation Hardness (H 132/10) | 105 | MPa | ISO 2039-1 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus | 5500 | MPa | ISO 527-2/1A/1 |
| Tensile Stress (Break) | 70.0 | MPa | ISO 527-2/1A/5 |
| Tensile Strain (Break) | 3.8 | % | ISO 527-2/1A/5 |
| Flexural Modulus 1 | 4500 | MPa | ISO 178 |
| Flexural Stress (5.0% Strain) | 100 | MPa | ISO 178 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30°C | 7.0 | kJ/m² | ISO 179/1eA |
| 23°C | 10 | kJ/m² | ISO 179/1eA |
| Charpy Unnotched Impact Strength | ISO 179/1eU | ||
| -30°C | 50 | kJ/m² | ISO 179/1eU |
| 23°C | 50 | kJ/m² | ISO 179/1eU |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Heat Deflection Temperature | |||
| 0.45 MPa, not annealed | 150 | °C | ISO 75-2/Bf |
| 1.8 MPa, not annealed | 130 | °C | ISO 75-2/Af |
| Vicat Softening Temperature | |||
| -- | 160 | °C | ISO 306/A50 |
| -- | 115 | °C | ISO 306/B50 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Surface Resistivity | 1.0E+3 | ohms | IEC 60093 |
| Additional Information |
|---|
| 1.) Not for use in food contact applications2.) Not for use in medical or pharmaceutical applicationsCharacteristic propertiesPP is highly inflammable, it burns with a bright flame and a blue core. Afterextinguishing it has a pungent paraffin like smell (similar to tar).hardness and good cold impact resistance. |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 80.0 | °C | |
| Drying Time | 2.0 - 3.0 | hr | |
| Suggested Max Regrind | 30 | % | |
| Rear Temperature | 230 | °C | |
| Middle Temperature | 245 | °C | |
| Front Temperature | 260 | °C | |
| Nozzle Temperature | 260 | °C | |
| Processing (Melt) Temp | 230 - 280 | °C | |
| Mold Temperature | 40.0 - 70.0 | °C | |
| Injection Pressure | 80.0 - 160 | MPa | |
| Injection Rate | Moderate | ||
| Holding Pressure | 25.0 - 85.0 | MPa | |
| Back Pressure | 5.00 - 20.0 | MPa | |
| Cushion | 2.00 - 5.00 | mm | |
| Screw Speed | 600 | mm/sec |
| Injection instructions |
|---|
| PredryingIn general no predrying, only when moisture on granulate surface predrying at 80°C for 2-3 hours is recommended.ReprocessingUp to 100% regind may be used in which case use of additional stabilisation(e.g. POLYCYCLE®) is recommended as a safety precaution. Usual recyclecontent 10 - 30%.Shut downPP can normally be left in the cylinder. It is quiet insensitive to temperature.FinishingThe material must be pre-treated for printing and gluing by flaming or coronadischarge. Otherwise there are some special printing colours or glues.RemarksIn contact with copper the melt will be degraded. For permanent processing ofglass fibre reinforced grades wear resistant screws and cylinders arerecommended. |
| Note Message | |
|---|---|
| 1 . | 2.0 mm/min |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| RTP 1387 SI | RTP Company | PPS | RTP |
| Baydur® STR/C-1000 (38% Glass) | Covestro - PUR | PUR-MDI | Baydur® |
| Borealis PP QB377 | Borealis AG | PP, Unspecified | Borealis PP |
| Petra® 130 | BASF Corporation | PET | Petra® |
| ULTEM™ HU1110 resin | SABIC Innovative Plastics | PEI | ULTEM™ |
