Generic PC - Glass Fiber Datasheet,PC,Generic-SHANGHAI SUSHENG

Message
This data represents typical values that have been calculated from all products classified as: Generic PC - Glass Fiber This information is provided for comparative purposes only.

General Information
Filler / Reinforcement	Glass fiber reinforced material

Physical	Nominal Value	Unit	Test Method
Specific Gravity
--	1.24 - 1.52	g/cm³	ASTM D792
23°C	1.24 - 1.44	g/cm³	ISO 1183
--	1.25 - 1.65	g/cm³	ASTM D1505
Apparent Density	0.64	g/cm³	ISO 60
Melt Mass-Flow Rate (MFR)
300°C/1.2 kg	3.8 - 19	g/10 min	ASTM D1238
300°C/1.2 kg	2.1 - 15	g/10 min	ISO 1133
Melt Volume-Flow Rate (MVR) (300°C/1.2 kg)	2.79 - 14.2	cm³/10min	ISO 1133
Molding Shrinkage
Flow : 23°C	4.0E-3 - 0.50	%	ASTM D955
Transverse flow : 23°C	0.20 - 0.73	%	ASTM D955
23°C	0.18 - 0.50	%	ISO 294-4
Water Absorption
23°C, 24 hr	0.059 - 0.22	%	ASTM D570
23°C, 24 hr	0.076 - 0.40	%	ISO 62
Saturated, 23°C	0.070 - 0.30	%	ASTM D570
Saturated, 23°C	0.068 - 0.31	%	ISO 62
Equilibrium, 23°C	0.24 - 0.32	%	ASTM D570
Equilibrium, 23°C, 50% RH	0.068 - 0.22	%	ISO 62

Hardness	Nominal Value	Unit	Test Method
Rockwell Hardness
23°C	84 - 124		ASTM D785
23°C	65 - 121		ISO 2039-2
Ball Indentation Hardness	115 - 151	MPa	ISO 2039-1

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus
23°C	2610 - 9730	MPa	ASTM D638
23°C	2970 - 9600	MPa	ISO 527-2
Tensile Strength
Yield, 23°C	49.1 - 127	MPa	ASTM D638
Yield, 23°C	52.7 - 121	MPa	ISO 527-2
Fracture, 23°C	33.8 - 143	MPa	ASTM D638
Fracture, 23°C	43.9 - 131	MPa	ISO 527-2
23°C	54.4 - 147	MPa	ASTM D638
23°C	45.0 - 100	MPa	ISO 527-2
Tensile Elongation
Yield, 23°C	2.1 - 5.0	%	ASTM D638
Yield, 23°C	1.9 - 5.1	%	ISO 527-2
Fracture, 23°C	0.0 - 7.5	%	ASTM D638
Fracture, 23°C	1.0 - 5.4	%	ISO 527-2
Flexural Modulus
23°C	2980 - 8550	MPa	ASTM D790
23°C	2790 - 8730	MPa	ISO 178
Flexural Strength
23°C	82.3 - 221	MPa	ASTM D790
23°C	89.5 - 182	MPa	ISO 178
Yield, 23°C	88.4 - 183	MPa	ASTM D790
Fracture, 23°C	109 - 190	MPa	ASTM D790
Compressive Strength (23°C)	69.8 - 152	MPa	ASTM D695
Coefficient of Friction	0.18 - 0.58		ASTM D1894
Taber Abrasion Resistance (23°C)	11.0 - 17.3	mg	ASTM D1044

Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength (23°C)	5.7 - 25	kJ/m²	ISO 179
Charpy Unnotched Impact Strength (23°C)	26 - 71	kJ/m²	ISO 179
Notched Izod Impact
23°C	64 - 160	J/m	ASTM D256
23°C	7.0 - 25	kJ/m²	ISO 180
Notched Izod Impact (23°C)	10.0 - 10.1	kJ/m²	ASTM D256
Unnotched Izod Impact
23°C	93 - 2100	J/m	ASTM D256
23°C	34 - 75	kJ/m²	ISO 180
Instrumented Dart Impact
23°C	9.15 - 61.0	J	ASTM D3763
23°C	2.15 - 9.29	J	ISO 6603-2
Multi-Axial Instrumented Impact Peak Force (23°C)	885 - 4030	N	ISO 6603-2
Dart Drop Impact (23°C)	0.452 - 102	J	ASTM D3029
Tensile Impact Strength (23°C)	53.3 - 158	kJ/m²	ASTM D1822

Thermal	Nominal Value	Unit	Test Method
Deflection Temperature Under Load
0.45 MPa, not annealed	136 - 153	°C	ASTM D648
0.45 MPa, not annealed	139 - 149	°C	ISO 75-2/B
0.45 MPa, annealed	144 - 149	°C	ASTM D648
0.45 MPa, annealed	143 - 148	°C	ISO 75-2/B
1.8 MPa, not annealed	133 - 152	°C	ASTM D648
1.8 MPa, not annealed	131 - 146	°C	ISO 75-2/A
1.8 MPa, annealed	135 - 143	°C	ASTM D648
1.8 MPa, annealed	131 - 144	°C	ISO 75-2/A
Continuous Use Temperature	129 - 133	°C	ASTM D794
Glass Transition Temperature	148	°C	DSC
Vicat Softening Temperature
--	143 - 169	°C	ASTM D1525
--	142 - 154	°C	ISO 306
Ball Indentation Temperature	125 - 140	°C	IEC 60598-1
Linear thermal expansion coefficient
Flow	1.9E-5 - 4.6E-5	cm/cm/°C	ASTM D696
Flow	2.1E-5 - 5.0E-5	cm/cm/°C	ASTM E831
Flow	1.9E-5 - 5.1E-5	cm/cm/°C	ISO 11359-2
Lateral	7.0E-6 - 7.5E-5	cm/cm/°C	ASTM D696
Lateral	5.2E-5 - 7.2E-5	cm/cm/°C	ASTM E831
Lateral	6.0E-5 - 7.1E-5	cm/cm/°C	ISO 11359-2
Specific Heat (23°C)	1050 - 1250	J/kg/°C	ASTM C351
Thermal Conductivity
23°C	0.13 - 0.35	W/m/K	ASTM C177
23°C	0.21 - 0.30	W/m/K	ISO 8302
RTI Elec	79.1 - 130	°C	UL 746
RTI Imp	75.0 - 130	°C	UL 746
RTI	75.0 - 130	°C	UL 746

Electrical	Nominal Value	Unit	Test Method
Surface Resistivity
--	5.0 - 7.2E+15	ohms	ASTM D257
--	1.0E+4 - 1.0E+15	ohms	IEC 60093
Volume Resistivity
23°C	0.0 - 2.5E+16	ohms·cm	ASTM D257
23°C	1.0E+13 - 2.5E+16	ohms·cm	IEC 60093
Dielectric Strength
23°C	16 - 30	kV/mm	ASTM D149
23°C	15 - 37	kV/mm	IEC 60243-1
Dielectric Constant
23°C	3.00 - 3.54		ASTM D150
23°C	2.95 - 5.13		IEC 60250
23°C	3.21		IEC 60250
Dissipation Factor
23°C	8.0E-4 - 0.010		ASTM D150
23°C	8.0E-4 - 9.4E-3		IEC 60250
Arc Resistance	100 - 120	sec	ASTM D495
Comparative Tracking Index	171 - 175	V	IEC 60112
Insulation Resistance (23°C)	1.0E+4 - 1.0E+12	ohms	IEC 60167

Flammability	Nominal Value	Unit	Test Method
Glow Wire Flammability Index	957 - 960	°C	IEC 60695-2-12
Glow Wire Ignition Temperature	824 - 960	°C	IEC 60695-2-13
Oxygen Index
--	30 - 40	%	ASTM D2863
--	35 - 38	%	ISO 4589-2

Injection instructions
This data represents typical values that have been calculated from all products classified as: Generic PC - Glass FiberThis information is provided for comparative purposes only.

Category:	PC , Polycarbonate
Manufacturer:	Generic
Trademark:	Generic
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	3QUF7G_Generic-PC---Glass-Fiber.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
PRIME TPO J-5710	Prime Polymer Co., Ltd.	PP Random Copolymer	PRIME TPO
Resan SAN	Polimarky Spolka Jawna	PS (GPPS)	Resan
Sylvin 8280-90 Natural	Sylvin Technologies Incorporated	PVC, Flexible	Sylvin
Zytel® FG101L NC010	DuPont Performance Polymers	Nylon 66	Zytel®
EMPILON® 545	EMPILON	SEBS	EMPILON®