Prime Tuff-X ST

Category:	Unspecified , Unspecified
Manufacturer:	Primex Plastics Corporation
Trademark:	Prime Tuff-X
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	2TuhAg_Prime-Tuff-X-ST.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

Message
Prime Tuff-X ST offers the same great benefits as our standard Tuff-X product but with a soft touch feel and look. It has a high friction coefficient and a 5% gloss reading after forming. It has good scratch and mar, UV stable and colorable. Unlike other soft touch products,40% regrind use maintains critical properties. Applications: Prime Tuff-X ST is well suited for applications such as; Instrument panels and decorative trim for RV, ATV, Marine and Heavy Trucks. Processing: Prime Tuff-X ST has better hot strength than our standard Tuff-X, therefore, high sag and webbing during the forming process is not as great. It is still best to form this product on an aluminum tool that is grit blasted. It can be formed on male or female tooling. The forming temperature should be 320-360°F, tool temp. of 170-190°F. Finishing: The same methods for cutting, bonding and fabrication can be used on Prime Tuff-X ST as is used for our other Tuff-X products. Please contact your Primex Plastics representative for more information on finishing, fabricating, or the thermoforming process. Colors, Textures and Capabilities: Tuff-X ST, allows for thesubstrate as well as the cap to be colored matched to anything specified. There are certain carriers that we use to assure that the properties of the two products are not distorted. Tuff-X ST is offered in several different textures that include, H/C, FL/HC, Calf Grain, Diamond Plate and Levant ll. We offer a gauge range of .090 to .400 and widths up to 120".

Message

Prime Tuff-X ST offers the same great benefits as our standard Tuff-X product but with a soft touch feel and look. It has a high friction coefficient and a 5% gloss reading after forming. It has good scratch and mar, UV stable and colorable. Unlike other soft touch products,40% regrind use maintains critical properties.

Applications:
Prime Tuff-X ST is well suited for applications such as; Instrument panels and decorative trim for RV, ATV, Marine and Heavy Trucks.

Processing:
Prime Tuff-X ST has better hot strength than our standard Tuff-X, therefore, high sag and webbing during the forming process is not as great. It is still best to form this product on an aluminum tool that is grit blasted. It can be formed on male or female tooling. The forming temperature should be 320-360°F, tool temp. of 170-190°F.

Finishing:
The same methods for cutting, bonding and fabrication can be used on Prime Tuff-X ST as is used for our other Tuff-X products.

Please contact your Primex Plastics representative for more information on finishing, fabricating, or the thermoforming process.

Colors, Textures and Capabilities:
Tuff-X ST, allows for thesubstrate as well as the cap to be colored matched to anything specified. There are certain carriers that we use to assure that the properties of the two products are not distorted.

Tuff-X ST is offered in several different textures that include, H/C, FL/HC, Calf Grain, Diamond Plate and Levant ll. We offer a gauge range of .090 to .400 and widths up to 120".

General Information
Features	Good Colorability Good UV Resistance High Friction High Gloss High Heat Resistance High Tensile Strength Low Temperature Impact Resistance Scratch Resistant Soft Ultra High Impact Resistance
Uses	Automotive Exterior Trim Automotive Instrument Panel
Appearance	Colors Available
Forms	Sheet
Processing Method	Thermoforming

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.10	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR)	0.74	g/10 min	ASTM D1238

Mechanical	Nominal Value	Unit	Test Method
Tensile Strength			ASTM D638
Yield	16.5	MPa
Break	14.5	MPa
Tensile Elongation (Break)	410	%	ASTM D638
Flexural Modulus	1280	MPa	ASTM D790

Impact	Nominal Value	Unit	Test Method
Notched Izod Impact	No Break		ASTM D256

Thermal	Nominal Value	Unit	Test Method
CLTE - Flow	3.3E-5	cm/cm/°C	ASTM D696

Additional Information	Nominal Value	Unit
Forming Temperature	160 to 182	°C
Maximum Allowable Regrind	40	%
Tool Temperature	77 to 88	°C

Resin Grade	Manufacturer	Category	Trademark
Makrolon® 2807	Covestro - Polycarbonates	PC	Makrolon®
tivilon® F 85 Dx 2	API SpA	TPV	tivilon®
Fluoroloy® A09	Saint Gobain Performance Plastics	TP, Unspecified	Fluoroloy®
Durethan® B 35 F KA 000000	LANXESS Corporation	Nylon 6	Durethan®
Kuraray Poval® PVA 220SB	Kuraray Co., Ltd.	PVOH	Kuraray Poval®