Glastic® 1412 Datasheet,Polyester, TS,Bulk Molding Compounds, Inc.-SHANGHAI SUSHENG

Message
Grade 1412 is one of the most versatile and universal molding materials available anywhere. Flame and track resistant, low shrink for close dimensional control and surface smoothness, high physical properties. Developed for injection molding but also suitable for compression or transfer applications. Glastic's highest temperature material, Grade 1412 is truly a premium material at a reasonable cost. Grade 1412 is approved for Mil specifications MAI-30, MAI-60 and MAT-30.

General Information
Filler / Reinforcement	Glass fiber reinforced material
Features	Insulation Good electrical performance Track Resistance Low shrinkage Flame retardancy
Uses	Electrical/Electronic Applications Electrical housing Home appliance components Application in Automobile Field
Agency Ratings	MIL M-14, Type MAI-30 MIL M-14, Type MAI-60 MIL M-14, Type MAT-30
Appearance	White Black Red Available colors brownish yellow
Forms	BMC-Block Molding Compound
Processing Method	Compression molding Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.77	g/cm³	ASTM D792
Water Absorption (24 hr)	0.16	%	ASTM D570

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus (Compression Molded)	12400	MPa	ASTM D638
Tensile Strength (Yield, Compression Molded)	44.6	MPa	ASTM D638
Flexural Modulus (Compression Molded)	13100	MPa	ASTM D790
Flexural Strength (Compression Molded)	166	MPa	ASTM D790
Compressive Strength	178	MPa	ASTM D695
Shear Strength	64.3	MPa	ASTM D732

Impact	Nominal Value	Unit	Test Method
Notched Izod Impact (Compression Molded)	470	J/m	ASTM D256

Thermal	Nominal Value	Unit	Test Method
RTI Elec	160	°C	UL 746
RTI	160	°C	UL 746

Electrical	Nominal Value	Unit	Test Method
Surface Resistivity	2.0E+13 6.8E+14	ohms	ASTM D257
Dielectric Strength ¹	19	kV/mm	ASTM D149
Dielectric Constant			ASTM D150
60 Hz	5.70 5.30		ASTM D150
1 MHz	4.30		ASTM D150
Dissipation Factor			ASTM D150
60 Hz	0.039 0.018		ASTM D150
1 MHz	0.023 0.15		ASTM D150
Arc Resistance	192	sec	ASTM D495

Flammability	Nominal Value	Unit	Test Method
Flame Rating	V-0		UL 94

Additional Information
Permittivity, ASTM D150, 60 Hz, Condition A: 5.3Permittivity, ASTM D150, 60 Hz, Condition D: 5.7Permittivity, ASTM D150, 1 MHz, Condition A: 4.3Permittivity, ASTM D150, 1 MHz, Condition D: 4.3Insulation Resistance, ASTM D257, Condition A: 68.2 Ohm x 10e13Insulation Resistance, ASTM D257, Condition C: 2.0 Ohm x 10e13Track Resistance, ASTM D2303: 1500 minutesDissipation Factor, ASTM D150, 60 Hz, Condition A: 0.018Dissipation Factor, ASTM D150, 60 Hz, Condition D: 0.039Dissipation Factor, ASTM D150, 1 MHz, Condition A: 0.023Dissipation Factor, ASTM D150, 1 MHz, Condition D: 0.152

Additional Information

Permittivity, ASTM D150, 60 Hz, Condition A: 5.3Permittivity, ASTM D150, 60 Hz, Condition D: 5.7Permittivity, ASTM D150, 1 MHz, Condition A: 4.3Permittivity, ASTM D150, 1 MHz, Condition D: 4.3Insulation Resistance, ASTM D257, Condition A: 68.2 Ohm x 10e13Insulation Resistance, ASTM D257, Condition C: 2.0 Ohm x 10e13Track Resistance, ASTM D2303: 1500 minutesDissipation Factor, ASTM D150, 60 Hz, Condition A: 0.018Dissipation Factor, ASTM D150, 60 Hz, Condition D: 0.039Dissipation Factor, ASTM D150, 1 MHz, Condition A: 0.023Dissipation Factor, ASTM D150, 1 MHz, Condition D: 0.152

Note Message
1 .	Method A (short time)

Category:	Polyester, TS , Thermoset Polyester
Manufacturer:	Bulk Molding Compounds, Inc.
Trademark:	Glastic®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	18zGAa_Glastic-1412.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
Sup-tech A230	Shanghai Suptech Engineering Plastics Co. Ltd.	Nylon 66	Sup-tech
Tarnamid® T- 30 MS	Grupa Azoty S.A.	Nylon 6	Tarnamid®
TOPAS® 5013S-04	Topas Advanced Polymers, Inc.	COC	TOPAS®
Ebalta MG 453 / Comp. A+B	Ebalta Kunststoff GmbH	PUR, Unspecified	Ebalta
Hifax TRC 790PHF 3004 BLK	LyondellBasell Industries	TPO (POE)	Hifax