Monprene® OM-10150 Datasheet,TPE,Teknor Apex Company-SHANGHAI SUSHENG

Message
Monprene OM-10150 is a thermoplastic elastomer designed for overmolding applications like grips and anti-skid parts for consumer products. Monprene OM-10150 is an opaque, UV resistant grade that exhibits excellent adhesion to nylon.

General Information
Features	Low Specific Gravity Sunlight Resistant Without Fillers Low density smoothness Light stabilization High liquidity Lubrication Water Soluble Medium hardness UV absorption
Uses	Handle overmolding Electrical appliances Power/other tools Soft handle Mobile phone Sporting goods Stationery Knob Toothbrush handle Bonding
Appearance	Opacity
Forms	Particle
Processing Method	Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	0.908	g/cm³	ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)	35	g/10 min	ASTM D1238

Hardness	Nominal Value	Test Method
Durometer Hardness		ASTM D2240
Shaw A	53	ASTM D2240
Shaw A, 5 seconds	50	ASTM D2240

Elastomers	Nominal Value	Unit	Test Method
Tensile Stress			ASTM D412
Transverse flow : 100% strain ¹	1.34	MPa	ASTM D412
Flow : 100% strain ²	1.63	MPa	ASTM D412
Transverse flow : 300% strain ³	2.05	MPa	ASTM D412
Flow : 300% strain ⁴	2.76	MPa	ASTM D412
Tensile Strength ⁵			ASTM D412
Transverse flow : Fracture	2.43	MPa	ASTM D412
Flow : Fracture	2.83	MPa	ASTM D412
Tensile Elongation ⁶			ASTM D412
Transverse flow : Fracture	350	%	ASTM D412
Flow : Fracture	340	%	ASTM D412
Tear Strength ⁷			ASTM D624
Transverse flow	16.3	kN/m	ASTM D624
Flow	14.5	kN/m	ASTM D624
Compression Set ⁸			ASTM D395B
23°C, 22 hr	20	%	ASTM D395B
70°C, 22 hr	16	%	ASTM D395B

Additional Information	Nominal Value
Adhesion to Nylon

Legal statement
The information and recommendations contained in this bulletin are, to the best of our knowledge, accurate and reliable but no guarantee of their accuracy is made. All products are sold upon condition that purchasers shall make their own tests to determine the suitability of such products for their particular purposes and uses and purchaser assumes all risks and liability for the results of use of the products, including use in accordance with seller's recommendations. Nothing in this bulletin constitutes permission or a recommendation to practice or use any invention covered by any patent owned by this company or others. There is no warranty of merchantability and there are no other warranties for the products described. For detailed Product Stewardship information, please contact us. Any product of Teknor Apex, including product names, shall not be used or tested in medical or food contact applications without the prior written acknowledgement of Teknor Apex as to the intended use. Please note that some products may not be available in one or more countries.

Legal statement

The information and recommendations contained in this bulletin are, to the best of our knowledge, accurate and reliable but no guarantee of their accuracy is made. All products are sold upon condition that purchasers shall make their own tests to determine the suitability of such products for their particular purposes and uses and purchaser assumes all risks and liability for the results of use of the products, including use in accordance with seller's recommendations. Nothing in this bulletin constitutes permission or a recommendation to practice or use any invention covered by any patent owned by this company or others. There is no warranty of merchantability and there are no other warranties for the products described. For detailed Product Stewardship information, please contact us. Any product of Teknor Apex, including product names, shall not be used or tested in medical or food contact applications without the prior written acknowledgement of Teknor Apex as to the intended use. Please note that some products may not be available in one or more countries.

Injection	Nominal Value	Unit
Drying Temperature	65.6	°C
Drying Time	2.0 - 4.0	hr
Rear Temperature	204 - 232	°C
Middle Temperature	210 - 232	°C
Front Temperature	216 - 238	°C
Nozzle Temperature	221 - 243	°C
Processing (Melt) Temp	221 - 243	°C
Mold Temperature	23.9 - 60.0	°C
Injection Pressure	1.38 - 6.89	MPa
Injection Rate	Fast
Back Pressure	0.172 - 0.862	MPa
Screw Speed	50 - 120	rpm
Cushion	3.81 - 25.4	mm

Injection instructions
Drying is not necessary. However, if moisture is a problem, dry the pellets for 2 to 4 hours at 150°F (65°C).

Note Message
1 .	Mouth die C, 510mm/min
2 .	Mouth die C, 510mm/min
3 .	C mold, 510mm/min
4 .	C mold, 510mm/min
5 .	C mold, 510mm/min
6 .	Mouth die C, 510mm/min
7 .	C mold, 510mm/min
8 .	Type 1

Category:	TPE , Thermoplastic Elastomer
Manufacturer:	Teknor Apex Company
Trademark:	Monprene®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	08E8cX_Monprene-OM-10150.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
UNITIKA Nylon 6 A1030GFL	UNITIKA Plastics Division	Nylon 6	UNITIKA Nylon 6
AZDEL™ U421-B01 (Transverse)	Azdel, Inc.	PP Alloy	AZDEL™
Chemlon® 133 GU	Teknor Apex Company (Chem Polymer)	Nylon 66	Chemlon®
Generic Nylon 6	Generic	Nylon 6	Generic
EPO-TEK® B9126-8	Epoxy Technology Inc.	Epoxy	EPO-TEK®